Juke F15 (2012 year). Service Repair Manual — part 79
DLK-256
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
DOOR REQUEST SWITCH
DOOR REQUEST SWITCH
Component Function Check
INFOID:0000000006605871
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “REQ SW-DR”, “REQ SW-AS” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Front door request switch is OK.
NO
>> Refer to
DLK-256, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000006605872
1.
CHECK DOOR REQUEST SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect malfunctioning front door request switch connector.
3.
Check voltage between malfunctioning front door request switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR REQUEST SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between malfunctioning front door request switch harness connector and BCM harness
connector.
3.
Check continuity between malfunctioning front door request switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
NO
>> Repair or replace harness.
Monitor item
Condition
Status
REQ SW -DR
Driver side door request switch
Pressed
ON
Released
OFF
REQ SW -AS
Passenger side door request switch
Pressed
ON
Released
OFF
(+)
(–)
Voltage
(Approx.)
Front door request switch
Connector
Terminal
Driver side
D34
2
Ground
12 V
Passenger side
D15
1
Front door request switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
Driver side
D34
2
M70
75
Existed
Passenger side
D15
1
76
Front door request switch
Ground
Continuity
Connector
Terminal
Driver side
D34
2
Not existed
Passenger side
D15
1
DOOR REQUEST SWITCH
DLK-257
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
CHECK DOOR REQUEST SWITCH GROUND CIRCUIT
Check continuity between malfunctioning front door request switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK DOOR REQUEST SWITCH
DLK-257, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace malfunctioning front door request switch.
5.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000006605873
1.
CHECK DOOR REQUEST SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect malfunctioning front door request switch connector.
3.
Check continuity between malfunctioning front door request switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace malfunctioning front door request switch.
Front door request switch
Ground
Continuity
Connector
Terminal
Driver side
D34
1
Existed
Passenger side
D15
2
Front door request switch
Condition
Continuity
Terminal
1
2
Door request switch
Pressed
Existed
Released
Not existed
DLK-258
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
DOOR SWITCH
DOOR SWITCH
Component Function Check
INFOID:0000000006605852
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “DOOR SW-DR”, “DOOR SW-AS”, “DOOR SW-RL”, “DOOR SW-RR”, “DOOR SW-BK” in “DATA
MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door switch is OK.
NO
>> Refer to
DLK-258, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000006605853
1.
CHECK DOOR SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect malfunctioning door switch connector.
3.
Check signal between malfunctioning door switch harness connector and ground using oscilloscope.
Is the inspection result normal?
YES-1 >> Back door: GO TO 3.
YES-2 >> Other door: GO TO 4.
NO
>> GO TO 2.
2.
CHECK DOOR SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between door switch harness connector and BCM harness connector.
Monitor item
Condition
Status
DOOR SW-DR
Driver side door
Open
On
Closed
Off
DOOR SW-AS
Passenger side door
Open
On
Closed
Off
DOOR SW-RL
Rear door LH
Open
On
Closed
Off
DOOR SW-RR
Rear door RH
Open
On
Closed
Off
DOOR SW-BK
Back door
Open
On
Closed
Off
(+)
(–)
Signal
(Reference value)
Door switch
Connector
Terminal
Driver side
B48
2
Ground
7.0 - 8.0 V
Passenger side
B49
Rear LH
B71
Rear RH
B53
Back door
D106
3
PKIB4960J
DOOR SWITCH
DLK-259
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between door switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK BACK DOOR SWITCH CIRCUIT
Check continuity between back door lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK DOOR SWITCH
DLK-259, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace malfunctioning door switch.
5.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000006605854
1.
CHECK DOOR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect malfunctioning door switch connector.
3.
Check continuity between door switch terminals.
Door switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
Driver side
B48
2
B10
47
Existed
Passenger side
B49
45
Rear LH
B71
48
Rear RH
B53
46
Back door
D106
3
43
Door switch
Ground
Continuity
Connector
Terminal
Driver side
B48
2
Not existed
Passenger side
B49
Rear LH
B71
Rear RH
B53
Back door
D106
3
Back door lock assembly
Ground
Continuity
Connector
Terminal
D106
4
Existed
DLK-260
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
DOOR SWITCH
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace malfunction door switch.
Door switch
Condition
Continuity
Terminal
Driver side
2
Ground part of door
switch
Door switch
Pressed
Existed
Released
Not existed
Passenger side
Pressed
Existed
Released
Not existed
Rear LH
Pressed
Existed
Released
Not existed
Rear RH
Pressed
Existed
Released
Not existed
Back door
3
4
Back door lock as-
sembly
Lock
Existed
Unlock
Not existed
HAZARD FUNCTION
DLK-261
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HAZARD FUNCTION
Component Function Check
INFOID:0000000006605874
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “FLASHER” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Hazard warning lamp circuit is OK.
NO
>> Refer to
DLK-261, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000006605875
1.
CHECK HAZARD SWITCH CIRCUIT
EXL-72, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
Monitor item
Status
FLASHER
LH
Front turn signal lamp LH
Turns ON
RH
Front turn signal lamp RH
Turns ON
OFF
Front turn signal lamp
Turns OFF
DLK-262
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
INTELLIGENT KEY
INTELLIGENT KEY
Component Function Check
INFOID:0000000006605876
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “RKE OPE COUN1” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Intelligent Key is OK.
NO
>> Refer to
DLK-262, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000006605877
1.
CHECK INTELLIGENT KEY BATTERY
Check by connecting a resistance (approximately 300
Ω
) so that the
current value becomes about 10 mA. Refer to
.
Is the measurement value within the specification?
YES
>> Replace Intelligent Key.
NO
>> Replace Intelligent Key battery.
Monitor item
Condition
RKE OPE COUN1
Check that the numerical value is changing while operating on the Intelligent Key.
Standard
: Approx. 2.5 - 3.0 V
OCC0607D
INTELLIGENT KEY WARNING BUZZER
DLK-263
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY WARNING BUZZER
Component Function Check
INFOID:0000000006605878
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “OUTSIDE BUZZER” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Intelligent Key warning buzzer is OK.
NO
>> Refer to
DLK-263, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000006605879
1.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check 10 A fuse, [No. 7, located in fuse block (J/B)].
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.
CHECK INTELLIGENT KEY WARNING BUZZER POWER SUPPLY CIRCUIT
1.
Disconnect Intelligent Key warning buzzer connector.
2.
Check voltage between Intelligent Key warning buzzer harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK INTELLIGENT KEY WARNING BUZZER CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and Intelligent Key warning buzzer harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
Monitor item
Status
OUTSIDE BUZZER
ON
Outside warning buzzer
Buzzer sounds
OFF
Buzzer does not sound
(+)
(–)
Voltage
(Approx.)
Intelligent Key warning buzzer
Connector
Terminal
E25
1
Ground
Battery voltage
BCM
Intelligent Key warning buzzer
Continuity
Connector
Terminal
Connector
Terminal
M70
93
E25
3
Existed
BCM
Ground
Continuity
Connector
Terminal
M70
93
Not existed
DLK-264
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
INTELLIGENT KEY WARNING BUZZER
4.
CHECK INTELLIGENT KEY WARNING BUZZER
DLK-264, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
NO
>> Replace Intelligent Key warning buzzer.
Component Inspection
INFOID:0000000006605880
1.
CHECK INTELLIGENT KEY WARNING BUZZER
1.
Turn ignition switch OFF.
2.
Disconnect Intelligent Key warning buzzer connector.
3.
Connect battery power supply directly to Intelligent Key warning buzzer terminals and check the opera-
tion.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace Intelligent Key warning buzzer.
Intelligent Key warning buzzer
Operation
Terminal
(+)
(
−
)
1
3
Buzzer sounds
KEY WARNING LAMP
DLK-265
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEY WARNING LAMP
Component Function Check
INFOID:0000000006605881
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “INDICATOR” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Key warning lamp is OK.
NO
>> Refer to
DLK-265, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000006605882
1.
CHECK KEY WARNING LAMP
MWI-22, "On Board Diagnosis Function"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
Monitor item
Status
INDICATOR
KEY ON
Key warning lamp
Turns ON
KEY IND
Blinks
OFF
Turns OFF
DLK-266
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
REMOTE KEYLESS ENTRY RECEIVER
REMOTE KEYLESS ENTRY RECEIVER
Component Function Check
INFOID:0000000006605883
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “RKE OPE COUN1” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Remote keyless entry receiver is OK.
NO
>> Refer to
DLK-266, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000006605884
1.
CHECK REMOTE KEYLESS ENTRY RECEIVER GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and remote keyless entry receiver connector.
3.
Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
4.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK REMOTE KEYLESS ENTRY RECEIVER POWER SUPPLY
1.
Reconnect BCM connector.
2.
Check voltage between remote keyless entry receiver harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 1
1.
Disconnect BCM connector
2.
Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
Monitor item
Condition
RKE OPE COUN1
Checks whether value changes when operating Intelligent Key
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M68
18
M75
1
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
18
Not existed
(+)
(–)
Voltage
(Approx.)
Remote keyless entry receiver
Connector
Terminal
M75
4
Ground
5 V
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M68
19
M75
4
Existed
REMOTE KEYLESS ENTRY RECEIVER
DLK-267
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
NO
>> Repair or replace harness.
4.
CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1.
Reconnect remote keyless entry receiver connector.
2.
Check signal between remote keyless entry receiver harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace remote keyless entry receiver.
5.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 2
1.
Disconnect BCM connector and remote keyless entry receiver connector.
2.
Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK REMOTE KEYLESS ENTRY RECEIVER RSSI OUTPUT SIGNAL
1.
Reconnect BCM and remote keyless entry receiver connector.
2.
Check signal between remote keyless entry receiver harness connector and ground using oscilloscope.
BCM
Ground
Continuity
Connector
Terminal
M68
19
Not existed
(+)
(–)
Condition
Signal
(Reference value)
Remote keyless entry receiver
Connector
Terminal
M75
2
Ground
Waiting
Press the Intelligent
Key lock or unlock
button
JMKIA3838GB
JMKIA3841GB
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M68
20
M75
2
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
20
Not existed
DLK-268
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
REMOTE KEYLESS ENTRY RECEIVER
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace remote keyless entry receiver.
7.
CHECK REMOTE KEYLESS ENTRY RECEIVER RSSI CIRCUIT
1.
Disconnect BCM and remote keyless entry receiver connector.
2.
Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
NO
>> Repair or replace harness.
(+)
(–)
Condition
Signal
(Reference value)
Remote keyless entry receiver
Connector
Terminal
M75
3
Ground
Waiting
Press and hold Intel-
ligent Key lock or un-
lock button
JMKIA5952GB
JMKIA5953GB
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M68
22
M75
3
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
22
Not existed
SHIFT P WARNING LAMP
DLK-269
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SHIFT P WARNING LAMP
Component Function Check
INFOID:0000000006605885
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “LCD” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Shift P warning lamp is OK.
NO
>> Refer to
DLK-269, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000006605886
1.
CHECK SHIFT P WARNING LAMP
MWI-22, "On Board Diagnosis Function"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
Monitor item
Status
LCD
SFT P
Shift P warning lamp
Turns ON
DLK-270
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
UNLOCK SENSOR
UNLOCK SENSOR
Component Function Check
INFOID:0000000006605895
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “UNLK SEN -DR” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Unlock sensor is OK.
NO
>> Refer to
DLK-270, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000006605896
1.
CHECK BCM OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check signal between front door lock assembly (driver side) harness connector and ground using oscillo-
scope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK UNLOCK SENSOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
Monitor item
Condition
Status
UNLK SEN -DR
Driver side door
Lock
OFF
Unlock
ON
(+)
(–)
Signal
(Reference value)
Front door lock assembly (driver side)
Connector
Terminal
D38
3
Ground
PKIB4960J
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M68
31
D38
3
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
31
Not existed
UNLOCK SENSOR
DLK-271
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
NO
>> Repair or replace harness.
3.
CHECK UNLOCK SENSOR GROUND CIRCUIT
Check continuity between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK UNLOCK SENSOR
DLK-271, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace front door lock assembly (driver side).
5.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000006605897
1.
CHECK UNLOCK SENSOR
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check continuity between front door lock assembly (driver side) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front lock assembly (driver side).
Front door lock assembly (driver side)
Ground
Continuity
Connector
Terminal
D38
4
Existed
Front door lock assembly (driver side)
Condition
Continuity
Terminal
3
4
Driver side door
Unlock
Existed
Lock
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст