Juke F15 (2012 year). Service Repair Manual — part 94

DLK-496

< SYSTEM DESCRIPTION >

[TYPE 4]

POWER DOOR LOCK SYSTEM

Setting change of Automatic Door Lock/Unlock Function

The unlock operation setting of the automatic door lock/unlock function can be changed.

With CONSULT- III

The ON/OFF switching of the automatic door lock/unlock function and the type selection of the automatic door
lock/unlock function can be performed at the WORK SUPPORT setting of CONSULT-III.

Without CONSULT- III

The automatic door lock/unlock function ON/OFF can be switched by performing the following operation.

1.

Close all doors below (door switch OFF)

2.

Turn ignition switch ON

3.

Press and hold the door lock and unlock switch for 5 seconds or more in the unlock direction within 20
seconds after turning the power supply position ON.

4.

The switching is completed when the hazard warning lamp blinks.

*1: This function is set to ON before delivery.
*2: This function does not operate on M/T models.

OFF

→

ON

: 2 blinks

ON

→

OFF

: 1 blink

REMOTE KEYLESS ENTRY SYSTEM

DLK-497

< SYSTEM DESCRIPTION >

[TYPE 4]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

REMOTE KEYLESS ENTRY SYSTEM

System Diagram

INFOID:0000000006303145

System Description

INFOID:0000000006303146

DOOR LOCK AND UNLOCK OPERATION

• When door lock and unlock button of keyfob is pressed, door lock and unlock signal transmits from keyfob to

BCM via remote keyless entry receiver.

• When BCM receives the door lock and unlock signal, it operates door lock actuator, blinks the hazard lamp

at the same time as a reminder.

OPERATION CONDITION

If the following conditions are satisfied, door lock/unlock operation is performed if the keyfob is operated.

OPERATION AREA

To ensure that the keyfob works effectively, use within 100 cm (3 ft) range of each door, however the operable
range may differ according to surroundings.

ANTI-HIJACK FUNCTION

• When an LOCK signal is transmitted from keyfob, all doors are locked.
• When an UNLOCK signal is transmitted from keyfob once, driver side door is unlocked.
• Then, if an UNLOCK signal is transmitted from keyfob again, all other doors are unlocked.
How to change anti-hijack mode.

With CONSULT-III

Anti-hijack mode can be set to ON or OFF using CONSULT-III.
Refer to

DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"

.

Without CONSULT-III

• ON/OFF can be switched when keyfob lock button and unlock button are pressed simultaneously for 5 sec-

onds or more while steering lock is locked.

• When mode is switched, hazard warning lamp blinks.

HAZARD REMINDER OPERATION

When door is locked or unlocked by keyfob, then BCM blinks hazard warning lamp as a reminder.
NOTE:

JMKIA6006GB

Remote controller operation

Operation condition

Lock

• Key switch is off
• All doors are closed

Unlock

Key switch is off

OFF

→

ON

: 1 blinks

ON

→

OFF

: 3 blink

DLK-498

< SYSTEM DESCRIPTION >

[TYPE 4]

REMOTE KEYLESS ENTRY SYSTEM

Hazard reminder mode can be changed with CONSULT-III. Refer to

DLK-502, "MULTI REMOTE ENT : CON-

SULT-III Function (BCM - MULTI REMOTE ENT) (Without Super Lock)"

.

AUTO DOOR LOCK FUNCTION

After door is unlocked by keyfob button operation and if 30 seconds or more passes without performing the fol-
lowing operation, all doors are automatically locked. However, operation check function does not activate.

Auto door lock mode can be changed by the “AUTO LOCK SET” mode in “WORK SUPPORT”. Refer to

DLK-

501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"

.

INTERIOR ROOM LAMP CONTROL FUNCTION

Interior room lamp is controlled according to door lock/unlock state, refer to

INL-6, "INTERIOR ROOM LAMP

CONTROL SYSTEM : System Description"

.

Hazard reminder setting

(With CONSULT-III)

Door lock operation

(with keyfob)

Hazard warning lamp blink

HAZARD LAMP SET

MODE 1

—

—

MODE 2

Lock

—

Unlock

Twice

Unlock (anti-hijack)

Twice (quick)

MODE 3

Lock

Once

Unlock

—

MODE 4

Lock

Once

Unlock

Twice

Unlock (anti-hijack)

Twice (quick)

Operating condition

• Door switch is ON (door is open)
• Door is locked
• Key switch is ON

BACK DOOR OPENER SYSTEM

DLK-499

< SYSTEM DESCRIPTION >

[TYPE 4]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

BACK DOOR OPENER SYSTEM

System Diagram

INFOID:0000000006554281

System Description

INFOID:0000000006554282

BACK DOOR OPENER OPERATION

When back door opener switch is pressed, BCM operates back door opener actuator.
NOTE:
Back door opener actuator is not for locking the back door. The function is only to open the back door.

OPERATION CONDITION

If the following conditions are satisfied, back door opener operation is performed.

NOTE:
• When battery terminal is disconnected and reconnected during all doors unlock state, back door may not

open.

• Regardless of door lock actuator state, BCM resets recognition of all doors unlock state approximately 30

seconds after battery terminal is disconnected and BCM recognizes that all doors are in lock state.

• When battery terminal is reconnected and back door does not open, have BCM recognize that all doors are

in unlock state.

JMKIA6011GB

Back door opener switch operation

Operation condition

Back door open

• When back door is unlocked using back door opener request switch (anti-hijack

mode), or after BCM outputs all doors unlock signal

• Vehicle speed is less than 5 km/h (3 MPH)

DLK-500

< SYSTEM DESCRIPTION >

[TYPE 4]

DIAGNOSIS SYSTEM (BCM)

DIAGNOSIS SYSTEM (BCM)

COMMON ITEM

COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)

INFOID:0000000006748149

APPLICATION ITEM

CONSULT-III performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.

×

: Applicable item

• *1: This item is displayed, but is not used.

• *2: For models with automatic A/C, this mode is not used.

DOOR LOCK

Diagnosis mode

Function Description

Work Support

Changes the setting for each system function.

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Ecu Identification

The BCM part number is displayed.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

Work Support

Data Monitor

Active Test

Door lock

DOOR LOCK

×

×

×

Rear window defogger

REAR DEFOGGER

×

×

Warning chime

BUZZER

×

×

Interior room lamp control

INT LAMP

×

×

×

Remote keyless entry system

MULTI REMOTE ENT

×

×

×

Exterior lamp

HEAD LAMP

×

×

×

Wiper and washer

WIPER

×

×

×

Turn signal and hazard warning lamps

FLASHER

×

×

• Automatic A/C
• Manual A/C
• Manual heater

AIR CONDITONER

×

×

*

2

Combination switch

COMB SW

×

Body control system

BCM

×

NATS

IMMU

×

×

Interior room lamp battery saver

BATTERY SAVER

×

×

×

Back door open

TRUNK

×

Vehicle security system

THEFT ALM

×

×

×

—

RETAINED PWR*

1

×

×

Signal buffer system

SIGNAL BUFFER

×

×

—

PANIC ALARM*

1

×

DIAGNOSIS SYSTEM (BCM)

DLK-501

< SYSTEM DESCRIPTION >

[TYPE 4]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)

INFOID:0000000006303148

WORK SUPPORT

*: P range interlock door lock/unlock can be selected for M/T models, but automatic door lock/unlock function does not operate.

DATA MONITOR

Monitor item

Description

DOOR LOCK-UNLOCK SET

Anti-hijack function can be changed to operate with this mode
• On: Operate
• Off: Non-operation

AUTOMATIC DOOR LOCK SE-
LECT

Automatic door lock function can be selected from the following in this mode
• VH SPD: All doors are locked when vehicle speed more than 10 km/h (6 MPH)
• P RANGE*: All doors are locked when shifting the selector lever from P position to other

than the P position

AUTOMATIC DOOR UNLOCK
SELECT

Automatic door unlock function can be selected from the following in the mode
• MODE 1: All doors are unlocked when the power supply position is changed from ON to

OFF

• MODE 2*: All doors are unlocked when shifting the selector lever from any position other

than the P to P position

• MODE 3: Driver side door is unlocked when the power supply position is changed from ON

to OFF

• MODE 4*: Driver side door is unlocked when shifting the selector lever from any position

other than the P to P position

• MODE 5: Driver side door is unlocked when key out of key switch
• MODE 6: All doors are unlocked when key out of key switch

AUTOMATIC LOCK/UNLOCK
SET

Automatic door lock/unlock function can be selected from the following in this mode
• Off: Non-operation
• Unlock Only: Door unlock operation only
• Lock Only: Door lock operation only
• Lock/Unlock: Door lock and unlock operation

Monitor Item

Contents

IGN ON SW

Indicated [On/Off] condition of ignition switch in ON position

KEY ON SW

Indicated [On/Off] condition of key switch

CDL LOCK SW

Indicated [On/Off] condition of lock signal from door lock unlock switch

CDL UNLOCK SW

Indicated [On/Off] condition of unlock signal from door lock unlock switch

DOOR SW-DR

Indicated [On/Off] condition of front door switch (driver side)

DOOR SW-AS

Indicated [On/Off] condition of front door switch (passenger side)

DOOR SW-RR

Indicated [On/Off] condition of rear door switch RH

DOOR SW-RL

Indicated [On/Off] condition of rear door switch LH

BACK DOOR SW

Indicated [On/Off] condition of back door switch

LOCK STATUS

Indicated [On/Off] condition of front door driver side

ACC ON SW

Indicated [On/Off] condition of ignition switch in ACC position

KEYLESS LOCK

Indicated [On/Off] condition of lock signal from key fob

KEYLESS UNLOCK

Indicated [On/Off] condition of unlock signal from key fob

SHOCK SENSOR

Indicates [NOMAL/ON/OFF] condition of circuit between BCM and air bag di-
agnosis sensor unit
• NORMAL: Ignition switch ON (BCM is receiving normal condition signal

from air bag diagnosis sensor unit)

• ON: During the receiving of air bag signal from air bag diagnosis sensor unit
• OFF: After the receiving of air bag signal from air bag diagnosis sensor unit

KEY CYL LK-SW

NOTE:
This item is displayed, but cannot be monitored

DLK-502

< SYSTEM DESCRIPTION >

[TYPE 4]

DIAGNOSIS SYSTEM (BCM)

ACTIVE TEST

MULTI REMOTE ENT

MULTI REMOTE ENT : CONSULT-III Function (BCM - MULTI REMOTE ENT) (Without
Super Lock)

INFOID:0000000006303149

DATA MONITOR

ACTIVE TEST

KEY CYL UN-SW

NOTE:
This item is displayed, but cannot be monitored

VEHICLE SPEED

Display the vehicle speed signal received from combination meter by numer-
ical value [Km/h]

Monitor Item

Contents

Test item

Description

DOOR LOCK

This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LCK” on CONSULT-III screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT-III screen is

touched

• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT-III screen

is touched

• The back door lock actuator is unlocked when “BD ULK” on CONSULT-III screen is touched
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT-III screen is

touched

DOOR LOCK IND

NOTE:
This item is displayed, but cannot be monitored

SUPER LOCK

NOTE:
This item is displayed, but cannot be monitored

Monitor Item

Condition

IGN ON SW

Indicates [On/Off] condition of ignition switch in ON position

KEY ON SW

Indicates [On/Off] condition of key switch

ACC ON SW

Indicates [On/Off] condition of ignition switch in ACC position

KEYLESS LOCK

Indicates [On/Off] condition of lock signal from keyfob

KEYLESS UNLOCK

Indicates [On/Off] condition of unlock signal from keyfob

KYLS TRNK/HAT

NOTE:
This item is displayed, but cannot be tested

DOOR SW-DR

Indicates [On/Off] condition of front door switch (driver side)

DOOR SW-AS

Indicates [On/Off] condition of front door switch (passenger side)

DOOR SW-RR

Indicates [On/Off] condition of rear door switch RH

DOOR SW-RL

Indicates [On/Off] condition of rear door switch LH

BACK DOOR SW

Indicates [On/Off] condition of back door switch

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be tested

CDL LOCK SW

Indicates [On/Off] condition of door lock and unlock switch

CDL UNLOCK SW

Indicates [On/Off] condition of door lock and unlock switch

KEYLESS PANIC

NOTE:
This item is displayed, but cannot be tested

DIAGNOSIS SYSTEM (BCM)

DLK-503

< SYSTEM DESCRIPTION >

[TYPE 4]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

WORK SUPPORT

TRUNK

TRUNK : CONSULT-III Function (BCM - TRUNK) (Without Super Lock)

INFOID:0000000006303150

DATA MONITOR

Test item

Description

INT LAMP

This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation

FLASHER

This test is able to check flasher operation [LH/RH/Off]

DOOR LOCK

This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LCK” on CONSULT-III screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT-III screen is

touched

• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT-III screen

is touched

• The back door lock actuator is unlocked when “BD ULK” on CONSULT- III screen is touched
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT-III screen is

touched

Test item

Description

REMO CONT IN REGIST

Keyfob ID code can be registered

REMO CONT IN ERASUR

Keyfob ID code can be erased

REMO CONT IN CONFIR

It can be checked whether Keyfob ID code is registered or not in this mode

HAZARD LAMP SET

Hazard and horn reminder function (hazard operation) mode can be changed in this mode
• MODE1: Non-operation
• MODE2: Unlock operation only
• MODE3: Lock operation only
• MODE4: Lock and unlock operation

AUTO LOCK SET

Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute

PANIC ALARM SET

NOTE:
This item is displayed, but cannot be tested

TRUNK OPEN SET

NOTE:
This item is displayed, but cannot be tested

Monitor Item

Contents

KEY ON SW

Indicates [On/Off] condition of key switch.

LOCK STATUS

Indicates [On/Off] condition of front door driver side.

VEHICLE SPEED

Indicates [Km/h] condition of vehicle speed signal from combination meter.

IGN ON SW

Indicates [On/Off] condition of ignition switch.

TRNK OPNR SW

NOTE:
This item is displayed, but cannot be monitored.

KYLS TRNK/HAT

NOTE:
This item is displayed, but cannot be monitored.

DLK-504

< ECU DIAGNOSIS INFORMATION >

[TYPE 4]

BCM

ECU DIAGNOSIS INFORMATION

BCM

List of ECU Reference

INFOID:0000000006303151

ECU

Reference

BCM

BCS-125, "Reference Value"

BCS-140, "Fail-safe"

BCS-140, "DTC Inspection Priority Chart"

BCS-141, "DTC Index"

DOOR & LOCK SYSTEM

DLK-505

< WIRING DIAGRAM >

[TYPE 4]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

WIRING DIAGRAM

DOOR & LOCK SYSTEM

Wiring Diagram

INFOID:0000000006303153

For connector terminal arrangements, harness layouts, and alphabets in a

(option abbreviation; if not

described in wiring diagram), refer to

GI-12, "Connector Information/Explanation of Option Abbreviation"

.

JCKWA3293GB

DLK-506

< WIRING DIAGRAM >

[TYPE 4]

DOOR & LOCK SYSTEM

JCKWA3294GB

DIAGNOSIS AND REPAIR WORK FLOW

DLK-507

< BASIC INSPECTION >

[TYPE 4]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

BASIC INSPECTION

DIAGNOSIS AND REPAIR WORK FLOW

Work Flow

INFOID:0000000006303154

OVERALL SEQUENCE

DETAILED FLOW

JMKIA3620GB

DLK-508

< BASIC INSPECTION >

[TYPE 4]

DIAGNOSIS AND REPAIR WORK FLOW

1.

GET INFORMATION FOR SYMPTOM

1.

Get the detailed information from the customer about the symptom (the condition and the environment
when the incident/malfunction occurred).

2.

Check operation condition of the function that is malfunctioning.

>> GO TO 2.

2.

CHECK FOR DTC

1.

Check DTC for BCM.

2.

Perform the following procedure if DTC is displayed.

-

Erase DTC.

-

Study the relationship between the cause detected by DTC and the symptom described by the customer.

3.

Check related service bulletins for information.

Is any symptom described and any DTC detected?

Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.

3.

CONFIRM THE SYMPTOM

Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR” mode and check real-time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.

>> GO TO 5.

4.

CONFIRM THE SYMPTOM

Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR ” mode and check real-time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.

>> GO TO 6.

5.

PERFORM DTC CONFIRMATION PROCEDURE

Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.
If two or more DTCs are detected, refer to

BCS-140, "DTC Inspection Priority Chart"

(BCM) and determine

trouble diagnosis order.
Is DTC detected?

YES

>> GO TO 7.

NO

>> Refer to

GI-42, "Intermittent Incident"

.

6.

DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS

Detect malfunctioning system according to Symptom Diagnosis based on the confirmed symptom in step 4.

>> GO TO 7.

7.

DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE

Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure is described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.

>> GO TO 8.

8.

REPAIR OR REPLACE THE MALFUNCTIONING PART

1.

Repair or replace the malfunctioning part.

2.

Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.

DIAGNOSIS AND REPAIR WORK FLOW

DLK-509

< BASIC INSPECTION >

[TYPE 4]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

3.

Check DTC. If DTC is displayed, erase it.

>> GO TO 9.

9.

FINAL CHECK

When DTC was detected in step 9, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunctions have been fully repaired.
When symptom was described by the customer, refer to the confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Are all malfunctions corrected?

NO (DTC is detected)>>GO TO 7.
NO (Symptom remains)>>GO TO 6.
YES

>> INSPECTION END

DLK-510

< BASIC INSPECTION >

[TYPE 4]

KEYFOB ID REGISTRATION

KEYFOB ID REGISTRATION

Description

INFOID:0000000006303155

Perform the following procedure after BCM is replaced or when new keyfob ID is registered
NOTE:
When registering the keyfob ID, perform only one procedure to simultaneously register both ID (IMMOBI-
LIZER ID and keyfob ID).

Work Procedure

INFOID:0000000006303156

1.

STEP 1

Close all doors.

>> GO TO 2.

2.

STEP 2

Operate lock using the driver side door lock and unlock switch.

>> GO TO 3.

3.

STEP 3

1.

Remove and insert the key into the ignition key 6 times within 10seconds (turning
the key switch from OFF to ON counts as 1 time).

2.

Hazard warning lamp blinks(2 times).

NOTE:
On the sixth key insertion, keep the key in the cylinder with the key switch ON.

Does the hazard lamp blink?

YES

>> GO TO 4.

NO

>> GO TO 1.

4.

STEP 4

Within 3 seconds after the hazard lamp blinks, turn ignition switch to the ACC position
and operate lock using the driver side door lock and unlock switch.

>> GO TO 5.

5.

STEP 5

1.

Press the lock or unlock button of the keyfob to be added.

2.

All doors unlock simultaneously.

3.

Hazard warning lamp blinks(2 times).

4.

Key ID is registered.

Is key ID registered?

YES-1 >> When adding a keyfob: GO TO 6.
YES-2 >> When ending registration: GO TO 8.
NO

>> GO TO 1.

6.

STEP 6

Operate lock using the driver side door lock and unlock switch.

>> GO TO 7.

7.

STEP 7

1.

Press the lock or unlock button of the keyfob to be added.

2.

All doors unlock simultaneously.

3.

Hazard warning lamp blinks(2 times).

4.

Key ID is registered.

KEYFOB ID REGISTRATION

DLK-511

< BASIC INSPECTION >

[TYPE 4]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Is key ID registered?

YES-1 >> When adding a keyfob: GO TO 6.
YES-2 >> When ending registration: GO TO 8.
NO

>> GO TO 6.

8.

STEP 8

Open the front door driver side.

>> REGISTRATION END