Nissan Versa Sedan. Manual — part 234
DLK-254
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY RECEIVER
Is the inspection result normal?
YES
>> GO TO 7
NO
>> Repair or replace harness between BCM and remote keyless entry receiver.
6.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 3
1. Check continuity between BCM connector and remote keyless entry receiver connector.
2. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 7
NO
>> Repair or replace harness between BCM and remote keyless entry.
7.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> Inspection End.
BCM
connector
Terminal
Remote keyless entry
receiver
connector
Terminal
Continuity
M18
18
M23
1
Yes
BCM
connector
Terminal
Remote keyless entry
receiver
connector
Terminal
Continuity
M18
20
M23
2
Yes
BCM connector
Terminal
Ground
Continuity
M18
20
No
KEYFOB BATTERY AND FUNCTION
DLK-255
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEYFOB BATTERY AND FUNCTION
Description
INFOID:0000000009268956
The following functions are available when having and carrying the keyfob.
• Door lock/unlock
• Panic mode (horn and headlamp operation)
Remote control entry function and panic alarm function are available when operating the remote buttons.
Component Function Check
INFOID:0000000009268957
NOTE:
The Signal Tech II Tool (J-50190) can be used to test the remote keyless entry keyfob relative signal strength.
Refer to the Signal Tech II User Guide for additional information.
1.
CHECK FUNCTION
With CONSULT
Check remote keyless entry receiver KEYLESS LOCK, KEYLESS UNLOCK, KYLS TRNK/HAT and KEYLESS
PANIC in Data Monitor mode with CONSULT.
Is the inspection result normal?
YES
>> Keyfob is OK.
NO
>> Refer to
DLK-255, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009268958
NOTE:
The Signal Tech II Tool (J-50190) can be used to test the remote keyless entry keyfob relative signal strength.
Refer to the Signal Tech II User Guide for additional information.
1.
CHECK KEYFOB FUNCTION
Check keyfob function using Signal Tech II Tool J-50190 or Remote
Keyless Entry Tester J-43241 (shown).
Does the test pass?
YES
>> Keyfob is OK.
NO
>> GO TO 2
2.
CHECK KEYFOB COMPONENTS
Monitor item
Condition
KEYLESS LOCK
Checks whether value changes from "Off" to "On" when operating keyfob lock button.
KEYLESS UNLOCK
Checks whether value changes from "Off" to "On" when operating keyfob unlock button.
KYLS TRNK/HAT
Checks whether value changes from "Off" to "On" when operating keyfob trunk button.
KEYLESS PANIC
Checks whether value changes from "Off" to "On" when operating keyfob panic button.
ALKIA2300ZZ
DLK-256
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
KEYFOB BATTERY AND FUNCTION
1. Remove the screw (A).
2. Insert a small screwdriver into the slit of the corner (B) and twist
it to separate the upper part from the power part. Use a cloth to
protect the casing.
CAUTION:
• Do not touch the circuit board or battery terminal.
• The keyfob is water-resistant. However, if it does get wet,
immediately wipe it dry.
3. Remove the keyfob battery.
CAUTION:
• Keep dirt, grease, and other foreign materials off the elec-
trode contact area.
4. Visually inspect keyfob internal components.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace malfunctioning parts.
3.
CHECK KEYFOB BATTERY
Check by connecting a resistance (approximately 300
Ω) so that the
current value becomes about 10 mA.
Is the measurement value within specification?
YES
>> Keyfob battery is OK. Check remote keyless entry
receiver. Refer to
.
NO
>> GO TO 4
4.
REPLACE KEYFOB BATTERY
1. Replace the keyfob battery with a new one (CR1620 or equiva-
lent).
CAUTION:
• When replacing battery, keep dirt, grease, and other for-
eign materials off the electrode contact area.
• Make sure that the + side faces the bottom of the case.
2. Align the tips of the upper and lower parts, and then push them
together until it is securely closed.
3. After replacing the battery, check that all keyfob functions work
properly.
Is the inspection result normal?
YES
>> Keyfob is OK.
NO
>> Check remote keyless entry receiver. Refer to
DLK-252, "Component Function Check"
ALKIA2301ZZ
Standard
: Approx. 2.5 - 3.0V
OCC0607D
ALKIA2302ZZ
HORN FUNCTION
DLK-257
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HORN FUNCTION
Description
INFOID:0000000009268959
Perform answer-back for each operation with horn.
Component Function Check
INFOID:0000000009268960
1.
CHECK FUNCTION
1. Select HORN in “ACTIVE TEST” mode with CONSULT.
2. Check the horn operation.
Is the operation normal?
YES
>> Inspection End.
NO
>> Refer to
DLK-257, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000009268961
Regarding Wiring Diagram information, refer to
.
1.
CHECK HORN FUNCTION
Check horn function with horn switch.
Does the horn sound?
YES
>> GO TO 2
NO
>> Refer to
.
2.
CHECK HORN RELAY POWER SUPPLY
1. Turn ignition switch ON.
2. Perform “ACTIVE TEST” (“HORN”) with CONSULT.
3. Using an oscilloscope or analog voltmeter to check voltage between IPDM E/R connector and ground.
Is the inspection result normal?
YES
>> Repair or replace open harness between IPDM E/R and horn relay.
NO
>> GO TO 3
3.
CHECK HORN RELAY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R and horn relay connector.
3. Check continuity between IPDM E/R harness connector and horn relay harness connector.
4. Check continuity between IPDM E/R harness connector and ground.
Test item
Description
HORN
ON
Horn relay
ON (for 20 ms)
IPDM E/R
Ground
Test item
Voltage (V)
(Approx.)
Connector
Terminal
E46
73
Ground
HORN
ON
Battery voltage
→ 0 → Battery voltage
Other than above
Battery voltage
IPDM E/R
Horn relay
Continuity
Connector
Terminal
Connector
Terminal
E46
73
E39
1
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст