Nissan Versa Sedan. Manual — part 235
DLK-258
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
HORN FUNCTION
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-56, "Removal and Installation"
NO
>> Repair or replace the malfunctioning part.
IPDM E/R
Ground
Continuity
Connector
Terminal
E46
73
Ground
No
WARNING CHIME FUNCTION
DLK-259
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
WARNING CHIME FUNCTION
Description
INFOID:0000000009268962
Performs operation method guide and warning with buzzer.
Component Function Check
INFOID:0000000009268963
1.
CHECK FUNCTION
With CONSULT
1. Check the operation with “BUZZER” in the Active Test.
2. Touch “IGN KEY WARN ALM”, “SEAT BELT WARN TEST”or “LIGHT WARN ALM”on screen.
Is the inspection result normal?
YES
>> Warning buzzer into combination meter is OK.
NO
>> Refer to
DLK-259, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009268964
1.
CHECK METER BUZZER CIRCUIT
Operate the hazard lights by turning ON the hazard warning switch.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Replace combination meter. Refer to
MWI-104, "Removal and Installation"
(type A).
2.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
.
>> Inspection End.
DLK-260
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
HAZARD FUNCTION
HAZARD FUNCTION
Description
INFOID:0000000009268965
Perform answer-back for each operation with number of blinks.
Component Function Check
INFOID:0000000009268966
1.
CHECK FUNCTION
Check hazard warning lamp (“FLASHER”) in Active Test.
Is the inspection result normal?
YES
>> Hazard warning lamp circuit is OK.
NO
>> Refer to
DLK-260, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000009268967
1.
CHECK HAZARD SWITCH CIRCUIT
Operate the hazard lights by turning ON the hazard warning switch.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair or replace hazard warning switch circuit. Refer to
2.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> Inspection End.
KEYFOB ID SET UP WITH CONSULT
DLK-261
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEYFOB ID SET UP WITH CONSULT
ID Code Entry Procedure
INFOID:0000000009268968
KEYFOB ID SET UP WITH CONSULT
NOTE:
• If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A spe-
cific ID code can be erased with CONSULT. However, when the ID code of a lost keyfob is not known,
all controller ID codes should be erased. After all ID codes are erased, the ID codes of all remaining
and/or new keyfobs must be re-registered.
• When registering an additional keyfob, the existing ID codes in memory may or may not be erased. If
five ID codes are stored in memory when an additional code is registered, only the oldest code is
erased. If less than five codes are stored in memory when an additional code is registered, the new
ID code is added and no ID codes are erased.
• Entry of a maximum of five ID codes is allowed. When more than five codes are entered, the oldest ID
code will be erased.
• Even if the same ID code that is already in memory is input, the same ID code can be entered. The
code is counted as an additional code.
1. Turn ignition switch ON.
2. Select BCM.
3. Select MULTI REMOTE ENT.
4. Select WORK SUPPORT.
5. You can register, erase or confirm a keyfob ID code. To register a new code, select the following option
and follow CONSULT instructions:
• REMO CONT ID REGIST
Use this mode to register a keyfob ID code.
NOTE:
Register the ID code when keyfob or BCM is replaced, or when additional keyfob is required.
• REMO CONT ID ERASUR
Use this mode to erase a keyfob ID code.
• REMO CONT ID CONFIR
Use this mode to confirm if a keyfob ID code is registered or not.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст