Nissan Versa Sedan. Manual — part 427
REAR COMBINATION LAMP
EXL-109
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REAR COMBINATION LAMP
Exploded View
INFOID:0000000009269680
Removal and Installation
INFOID:0000000009269681
REMOVAL
1. Remove trunk rear finisher. Refer to.
INT-32, "TRUNK REAR PLATE : Removal and Installation"
.
2. Remove rear combination lamp nuts.
3. Disengage the locating pin (A) of the rear combination lamp
using a suitable tool (B) at the gap between the rear combination
lamp and rear fender.
CAUTION:
Apply protective tape (C) on body to protect the painted
surface from damage.
4. Disconnect the harness connectors from the rear combination lamp and remove.
INSTALLATION
Installation is in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000009269682
1.
Rear combination lamp
2.
Grommet
Clip
JMLIA2044ZZ
JMLIA2046ZZ
EXL-110
< REMOVAL AND INSTALLATION >
REAR COMBINATION LAMP
Bulb Replacement
INFOID:0000000009269683
WARNING:
Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse while performing the opera-
tion.
• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP BULB
Removal
1. Remove rear combination lamp. Refer to
EXL-109, "Removal and Installation"
2. Remove screws (A) and the bulb holder.
3. Rotate stop/tail lamp bulb counterclockwise and remove.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install the back cover and the bulb socket securely for watertightness.
REAR TURN SIGNAL LAMP BULB
1.
Rear combination lamp (RH)
2.
Stop/tail lamp bulb (RH)
3.
Back-up lamp bulb (RH)
4.
Bulb holder (RH)
5.
Rear turn signal lamp bulb (RH)
6.
Bulb holder (LH)
7.
Stop/tail lamp bulb (LH)
8.
Rear combination lamp (LH)
9.
Back-up lamp bulb (LH)
10. Rear turn signal lamp bulb (LH)
JMLIA2045ZZ
JMLIA2047ZZ
REAR COMBINATION LAMP
EXL-111
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Removal
1. Remove rear combination lamp. Refer to
EXL-109, "Removal and Installation"
2. Remove screws (A) and the bulb holder.
3. Rotate rear turn signal lamp bulb counterclockwise and remove
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install the cover and the bulb socket securely for watertightness.
BACK-UP LAMP BULB
Removal
1. Remove rear combination lamp. Refer to
EXL-109, "Removal and Installation"
2. Remove screws (A) and the bulb holder.
3. Rotate back-up lamp bulb counterclockwise and remove.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install the cover and the bulb socket securely for watertightness.
JMLIA2047ZZ
JMLIA2047ZZ
EXL-112
< REMOVAL AND INSTALLATION >
HIGH-MOUNTED STOP LAMP
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000009269684
Rear Spoiler
Rear Parcel Shelf
Removal and Installation
INFOID:0000000009269685
HIGH-MOUNTED STOP LAMP - REAR SPOILER
Removal
1. Remove the rear spoiler. Refer to
EXT-33, "Removal and Installation"
2. Remove screws and the high-mounted stop lamp.
Installation
Installation is in the reverse order of removal.
HIGH-MOUNTED STOP LAMP - PARCEL SHELF
ALLIA0905ZZ
1.
Rear spoiler
2.
High-mounted stop lamp assembly
JMLIA2054ZZ
1.
Rear parcel shelf finisher
2.
High-mounted stop lamp socket
3.
High-mounted stop lamp bulb
4.
High-mounted stop lamp housing
Pawl
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст