Nissan Versa Sedan. Manual — part 426
FRONT FOG LAMP
EXL-105
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP
Exploded View
INFOID:0000000009269673
Removal and Installation
INFOID:0000000009269674
REMOVAL
1. Remove the fender protector. Refer to
EXT-26, "Removal and Installation"
2. Disconnect the harness connector from the front fog lamp.
3. Remove the screws and front fog lamp.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
After installation, perform fog lamp aiming adjustment procedure. Refer to
EXL-101, "Aiming Adjustment Pro-
Bulb Replacement
INFOID:0000000009269675
WARNING:
Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse while performing the opera-
tion.
• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
Removal
1. Remove the fender protector. Refer to
EXT-26, "Removal and Installation"
1.
Front fog lamp bulb
2.
Front fog lamp
3.
Front bumper fascia
4.
Front fog lamp finisher
JMLIA2043ZZ
EXL-106
< REMOVAL AND INSTALLATION >
FRONT FOG LAMP
2. Disconnect the harness connector (1) from front fog lamp bulb.
3. Rotate the bulb (2) counterclockwise and remove.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install the bulb socket securely for watertightness.
SKIB8304J
COMBINATION SWITCH
EXL-107
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
COMBINATION SWITCH
Exploded View
INFOID:0000000009269676
Removal and Installation
INFOID:0000000009269677
CAUTION:
• Before servicing, disconnect both battery terminals and wait at least three minutes.
• Do not use air tools or electric tools for servicing.
REMOVAL
1. Disconnect positive and negative battery terminals. Refer to
PG-63, "Removal and Installation"
2. Remove the steering column covers. Refer to
IP-18, "Removal and Installation"
.
3. Rotate steering wheel clockwise to access first combination switch bolt then remove bolt.
4. Rotate steering wheel counter-clockwise to access second combination switch bolt.
5. Remove bolt, disconnect the harness connectors from the combination switch and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case a malfunction is detected by the air bag warning lamp, reset with the self-diagnosis function
and delete the memory with CONSULT.
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunc-
tions. Refer to
1. Combination switch
2. Combination switch harness connector
Front
AWMIA1293ZZ
EXL-108
< REMOVAL AND INSTALLATION >
HAZARD SWITCH
HAZARD SWITCH
Exploded View
INFOID:0000000009269678
Removal and Installation
INFOID:0000000009269679
REMOVAL
1. Remove the cluster lid C. Refer to
IP-15, "Removal and Installation"
.
2. While pressing pawls, push the hazard switch to remove.
INSTALLATION
Installation is in the reverse order of removal.
1.
Cluster lid C
2.
Hazard switch
Pawl
JMLIA2056ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст