Nissan Versa Sedan. Manual — part 210
DLK-158
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID
Exploded View
INFOID:0000000009268855
TRUNK LID ASSEMBLY
TRUNK LID ASSEMBLY : Removal and Installation
INFOID:0000000009268856
CAUTION:
• Use two people when removing or installing trunk lid assembly due to its heavy weight.
• Use protective tape or shop cloths to protect surrounding components from damage during removal
and installation of trunk lid assembly.
REMOVAL
1. Remove trunk lid finisher (if equipped). Refer to
INT-35, "Removal and Installation"
.
2. Disconnect the harness connector from the license plate lamp. Refer to
EXL-114, "Removal and Installa-
3. Remove harness clips from trunk lid assembly, and then pull out harness from trunk lid assembly.
4. Remove the trunk lid hinge bolts on trunk lid side and the trunk lid assembly.
CAUTION:
Use two people when removing or installing trunk lid, due to its heavy weight.
INSTALLATION
Installation is in the reverse order of removal.
1.
Trunk lid weatherstrip
2.
Torsion bar clip
3.
Torsion bar (RH)
4.
Torsion bar (LH)
5.
Trunk lid hinge (LH)
6.
Bumper rubber
7.
Trunk lid striker
8.
Trunk lid assembly
A
Center mark
B
Seam
JMKIA8154ZZ
TRUNK LID
DLK-159
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
CAUTION:
• After installation, perform trunk lid adjustment procedure. Refer to
• After installation, check trunk lid open/close and lock/unlock operation.
• Apply touch-up paint (body color) onto the heads of the trunk lid hinge bolts.
TRUNK LID ASSEMBLY : Adjustment
INFOID:0000000009268857
Check the clearance and surface height between trunk lid and each part by visual inspection and tactile feel.
If the clearance and surface height are out of specification, adjust them according to the adjustment proce-
dure.
1.
Trunk lid assembly
2.
Trunk lid hinge
3.
Trunk lid striker
4.
Body side outer
5.
Rear combination lamp
6.
Rear bumper fascia
JMKIA8147GB
DLK-160
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID
Unit: mm (in)
1. Loosen trunk lid hinge bolts (trunk lid side).
2. Remove trunk rear plate. Refer to
INT-32, "TRUNK REAR PLATE : Removal and Installation"
.
3. Loosen trunk lid striker bolts.
4. Lift up trunk lid approximately 100 – 150 mm (3.9 – 5.9 in) then close it lightly and check that it is engaged
firmly with trunk lid closed.
5. Check the clearance and surface height.
6. Tighten trunk lid hinge and trunk lid striker.
7. Install trunk rear plate. Refer to
INT-32, "TRUNK REAR PLATE : Removal and Installation"
.
TRUNK LID STRIKER ADJUSTMENT
Adjust trunk lid striker so that it becomes parallel with trunk lid lock insertion direction.
TRUNK LID STRIKER
TRUNK LID STRIKER : Removal and Installation
INFOID:0000000009268858
REMOVAL
1. Remove trunk rear plate. Refer to
INT-32, "TRUNK REAR PLATE : Removal and Installation"
.
2. Remove trunk lid opener cable bolt (A) and trunk lid striker bolts
(B).
3. Remove trunk lid striker (1), disconnect trunk lid opener cable
(2) from trunk lid striker and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Section
Item
Measurement
Standard
Difference (RH/LH,
MAX)
A – A
E
Clearance
3.5
± 1.0 (0.14 ± 0.04)
1.5 (0.06)
F
Surface height
0.0
± 1.0 (0.00 ± 0.04)
1.5 (0.06)
B – B
G
Clearance
3.5
± 1.0 (0.14 ± 0.04)
1.5 (0.06)
H
Surface height
-0.5
± 1.0 (0.02 ± 0.04)
1.5 (0.06)
C – C
I
Clearance
4.5
± 1.9 (0.18 ± 0.07)
2.9 (0.11)
J
Surface height
2.1
± 0.75 (0.08 ± 0.03)
3.0 (0.12)
D – D
K
Clearance
7.0
± 2.0 (0.28 ± 0.08)
2.5 (0.10)
JMKIA8124ZZ
JMKIA8125ZZ
TRUNK LID
DLK-161
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• After installation, check trunk lid open/close, lock/unlock operation.
• After installation, perform the trunk lid adjustment procedure. Refer to
.
TRUNK LID HINGE
TRUNK LID HINGE : Removal and Installation
INFOID:0000000009268859
REMOVAL
1. Remove harness clips (A) from trunk lid hinge (RH only) (1).
2. Remove trunk lid assembly. Refer to
DLK-158, "TRUNK LID ASSEMBLY : Removal and Installation"
3. Remove torsion bar. Refer to
DLK-161, "TORSION BAR : Removal and Installation"
.
4. Remove rear parcel shelf finisher. Refer to
INT-25, "Removal and Installation"
5. Remove trunk lid hinge bolts (body side) and then trunk lid hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check trunk lid open/close, lock/unlock operation.
• After installation, perform the trunk lid adjustment procedure. Refer to
.
• Apply touch-up paint (body color) onto the heads of trunk lid hinge bolts.
• Check trunk lid hinge rotating point for poor lubrication. If
necessary, apply a suitable multi-purpose grease.
TORSION BAR
TORSION BAR : Removal and Installation
INFOID:0000000009268860
REMOVAL
1. Remove torsion bar clamp.
2. Support trunk lid with a suitable tool.
WARNING:
Bodily injury may occur if trunk lid is not supported properly when removing the torsion bars.
JMKIA8126ZZ
JMKIA8127ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст