Nissan Versa Sedan. Manual — part 211
DLK-162
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID
3. Apply a torsion bar wrench (A) to torsion bar (1) and lift torsion
bar to remove it.
NOTE:
For torsion bar wrench, refer to the figure.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Check trunk lid open/close operation after installation.
TRUNK LID WEATHER-STRIP
TRUNK LID WEATHER-STRIP : Removal and Installation
INFOID:0000000009268861
REMOVAL
Remove trunk lid weatherstrip from the trunk lid opening.
CAUTION:
Do not pull excessively on weatherstrip.
INSTALLATION
1. Working from the upper section, align weatherstrip center mark
(A) with vehicle center mark (B) and install weatherstrip onto the
vehicle.
: Front
JMKIA8128ZZ
PIIB3774J
JMKIA8129ZZ
TRUNK LID
DLK-163
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Align the connecting point (B) of weatherstrip (2) to the center
(A) of striker (1) and install as shown.
3. Make sure entire weatherstrip is firmly seated.
NOTE:
Check that weatherstrip fits tightly all around the opening, especially in each corner and along the luggage
rear plate.
JMKIA8130ZZ
DLK-164
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD LOCK
HOOD LOCK
Exploded View
INFOID:0000000009268862
HOOD LOCK
HOOD LOCK : Removal and Installation
INFOID:0000000009268863
REMOVAL
1. Remove hood lock assembly bolts and hood lock assembly.
2. Disconnect hood lock control cable assembly (2) from hood lock
assembly (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Be careful not to bend the cable too much, keep the radius 100 mm (3.94 in) or more.
• Check that hood lock control cable is properly engaged with hood lock.
1.
Secondary latch
2.
Hood lock assembly
3.
Hood lock control cable assembly
Clip
AWKIA1892GB
JMKIA7997ZZ
HOOD LOCK
DLK-165
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• After installation, perform hood adjustment procedure. Refer to
• After adjusting, perform hood lock control inspection. Refer to
HOOD LOCK CONTROL CABLE
HOOD LOCK CONTROL CABLE : Removal and Installation
INFOID:0000000009268864
REMOVAL
1. Disconnect hood lock control cable assembly from hood lock assembly. Refer to
2. Remove fender protector (LH). Refer to
EXT-26, "Removal and Installation"
.
3. Release hood lock control cable clips.
4. Remove hood lock/fuel filler door release handle assembly bolts
(A).
5. Disconnect hood lock control cable assembly from hood lock/
fuel filler door release handle assembly.
6. Remove dash side finisher (LH). Refer to
INT-21, "DASH SIDE FINISHER : Removal and Installation"
7. Remove grommet on the lower dash and pull the hood lock control cable into the passenger compart-
ment.
CAUTION:
While pulling, be careful not to damage (peel) the outside of the hood lock control cable.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Be careful not to bend cable too much, keep the radius 100 mm (3.94 in) or more.
• Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet (at * mark).
• Check that hood lock control cable is properly engaged with hood lock.
• Perform hood adjustment procedure. Refer to
DLK-140, "HOOD ASSEMBLY : Adjustment"
.
• After installation, perform hood lock inspection. Refer to
HOOD LOCK SECONDARY CONTROL
HOOD LOCK SECONDARY CONTROL : Removal and Installation
INFOID:0000000009268865
REMOVAL
1. Remove radiator upper seal clips and then remove upper clip from radiator side seal (RH). Refer to
2. Remove hood lock secondary control nuts and hood lock secondary control.
JMKIA7998ZZ
PIIB5801E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст