Nissan Versa Sedan. Manual — part 885
TM-446
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
DIFFERENTIAL SIDE OIL SEAL
Adjust the CVT fluid level. Refer to
.
WATER HOSE
TM-447
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
WATER HOSE
Exploded View
INFOID:0000000009268273
Removal and Installation
INFOID:0000000009268274
REMOVAL
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator.
CAUTION:
Perform these steps after the coolant temperature has cooled sufficiently.
1. Remove the hose clamp and pull out the water hose A.
2. Remove the hose clamp and pull out the water hose B.
3. Remove the hose clamp and pull out the water hose C.
4. Pull out the heater hose and remove the water bypass pipe.
5. Remove the heater thermostat assembly.
6. Remove the bracket.
INSTALLATION
Installation is in the reverse order of removal.
1.
Hose clamp
2.
Water hose A
3.
Bracket
4.
Heater thermostat
5.
Water hose B
6.
Water hose C
7.
Water bypass pipe
8.
Hose clamp
9.
Heater hose
9.
Water hose D
A. Water outlet
B. Oil warner
C. To heater core
AWBIA1483ZZ
TM-448
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
WATER HOSE
• To install bracket to the CVT assembly, face the front arrow (A) of
the bracket toward front of vehicle.
• Refer to the following when installing water hoses.
• Refer to the following when installing hose clamp.
CAUTION:
Hose clamp should not interfere with the bulge of fluid cooler tube.
JSDIA1838ZZ
Water hose (1)
Installation side tube (2)
Direction of paint mark
Hose insertion depth (L)
Water hose A
Water outlet
Align with the mark on the water
outlet side
(A): 27 mm (1.06 in) (End reaches
the 2-stage bulge.)
Heater thermostat
Frontward
(B): 27 mm (1.06 in) (Hose end
reaches the 2-stage bulge.)
Water hose B
Heater thermostat
Frontward
CVT oil warmer
Frontward
(A): 27 mm (1.06 in) (End reaches
the 2-stage bulge.)
Water hose C
CVT oil warmer
Align with the mark on the CVT
oil warmer side
Water bypass pipe
Align with the mark on the water
bypass pipe side
Water hose D
Water bypass pipe
Align with the mark on the water
bypass pipe side
Water outlet
Align with the mark on the water
outlet side
JSDIA3579ZZ
WATER HOSE
TM-449
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Inspection
INFOID:0000000009268275
INSPECTION AFTER REMOVAL
Heater Thermostat
1. Fully immerse the heater thermostat (1) in a container (A) filled
with water. Continue heating the water while stirring.
2. Continue heating the heater thermostat for 5 minutes or more
after bringing the water to a boil.
3. Quickly take the heater thermostat out of the hot water, measure the heater thermostat within 10 seconds.
-
Place dial indicator (A) on the pellet (B) and measure the elon-
gation from the initial state.
4. If out of standard, replace heater thermostat.
INSPECTION AFTER INSTALLATION
Start the engine, and check the joints for coolant leakage.
Water hose (1)
Installation side
tube (2)
Hose clamp (3)
Dieection of tab
Clamping position
Water hose A
Water outlet
Upward
5 - 7 mm (0.20 - 0.25
in) (A) from hose end
Heater thermostat
Frontward
5 mm (0.20 in) (A)
from hose end
Water hose B
Heater thermostat
Frontward
CVT oil warmer
Frontward
5 - 7 mm (0.20 - 0.25
in) (A) from hose end
Water hose C
CVT oil warmer
Frontward
Water bypass pipe Rightward
Water hose D
Water bypass pipe
Upward and 45
°
frontward
Water outlet
Upward and 45
°
frontward
JSDIA2424ZZ
JSDIA3661ZZ
Standard
: Refer to
.
JSDIA3662ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст