Nissan Versa Sedan. Manual — part 883
TM-438
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
AIR BREATHER HOSE
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000009268254
REMOVAL
1. Remove air duct (inlet). Refer to
2. Remove air breather hose from transaxle assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that air breather hose is not collapsed or blocked due to folding or bending when installed.
• Be sure to insert air breather hose (1) fully until it reaches the
base of the transaxle tube (A).
JSDIA1978ZZ
G SENSOR
TM-439
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
G SENSOR
Exploded View
INFOID:0000000009268255
Removal and Installation
INFOID:0000000009268256
CAUTION:
• Do not drop or strike G sensor, because it may be damaged by impact.
• Do not use a power tool.
REMOVAL
1. Disconnect the battery negative terminal. Refer to
PG-63, "Removal and Installation"
2. Remove center console. Refer to
IP-23, "Removal and Installation"
3. Disconnect the harness connector from G sensor.
4. Remove G sensor.
INSTALLATION
Installation is in the reverse order of removal.
Adjustment
INFOID:0000000009268257
ADJUSTMENT AFTER INSTALLATION
Perform “G SENSOR CALIBRATION”. Refer to
.
1.
G sensor
Front
JSDIA1922GB
TM-440
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
OIL PAN
OIL PAN
Exploded View
INFOID:0000000009268258
Removal and Installation
INFOID:0000000009268259
REMOVAL
1. Remove the drain plug and overflow tube, and then drain the CVT fluid.
WARNING:
CVT fluid can splash when draining, use safety glasses to protect eyes.
2. Remove the drain plug gasket from the drain plug.
3. Remove the oil pan bolts (
), and then remove the oil pan and
oil pan gasket.
4. Remove the magnets from the oil pan.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse oil pan gasket and drain plug gasket.
1.
Transaxle assembly
2.
Oil pan gasket
3.
Magnet
4.
Oil pan
5.
Overflow tube
6.
Drain plug gasket
7.
Drain plug
8.
Oil pan fitting bolt
JSDIA1879GB
: Front
JSDIA1874ZZ
OIL PAN
TM-441
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Do not reuse oil pan bolts.
• Completely remove all moisture, oil and old gasket, etc. from the oil pan gasket mating surface of
transaxle case and oil pan.
• When installing the overflow tube, be sure to tighten to the specified torque. If it is not tightened to
the specified torque, the tube may be damaged.
• When the oil pan is installed, temporarily tighten oil pan bolts, then
tighten the oil pan bolts to specification in the order shown.
Inspection and Adjustment
INFOID:0000000009268260
INSPECTION AFTER REMOVAL
Check oil pan for foreign material.
• If a large amount of worn material is found, clutch plate may be worn.
• If iron powder is found, bearings, gears, or clutch plates may be worn.
• If aluminum powder is found, bushing may be worn, or chips or burrs of aluminum casting parts may enter.
Check points where wear is found in all cases.
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Check the CVT fluid level. Refer to
: Front
JSDIA1884ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст