Nissan Versa Sedan. Manual — part 838
TM-258
< PRECAUTION >
[CVT: RE0F11A]
PRECAUTIONS
CAUTION:
• Be sure to turn the ignition switch OFF and disconnect the battery cable from the negative terminal
before any repair or inspection work. The open/short circuit of related switches, sensors, solenoid
valves, etc. will cause the MIL to light up.
• Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MIL to light up due to an open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)
• Be sure to route and secure the harnesses properly after work. Interference of the harness with a
bracket, etc. may cause the MIL to light up due to a short circuit.
• Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to a malfunction of the EGR system or fuel injection system, etc.
• Be sure to erase the unnecessary malfunction information (repairs completed) from the TCM and
ECM before returning the vehicle to the customer.
Removal and Installation Procedure for CVT Unit Connector
INFOID:0000000009268055
REMOVAL
• Rotate bayonet ring (A) counterclockwise. Pull out CVT unit har-
ness connector (B) upward and remove it.
INSTALLATION
1. Align marking (A) on CVT unit harness connector terminal with
marking (B) on bayonet ring. Insert CVT unit harness connector.
2. Rotate bayonet ring clockwise.
3. Rotate bayonet ring clockwise until marking (A) on CVT unit har-
ness connector terminal body is aligned with the slit (B) on bayo-
net ring as shown in the figure (correctly fitting condition).
CAUTION:
JSDIA1162ZZ
JPDIA0294ZZ
JPDIA0295ZZ
PRECAUTIONS
TM-259
< PRECAUTION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Securely align marking (A) on CVT unit harness connec-
tor terminal body with bayonet ring slit (B). Then, be care-
ful not to make a half fit condition as shown in the figure.
• Do not mistake the slit of bayonet ring for other dent por-
tion.
JPDIA0296ZZ
TM-260
< PREPARATION >
[CVT: RE0F11A]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009268056
*: The O-ring as an unit part is set as a SST.
Commercial Service Tools
INFOID:0000000009268057
Tool number
Tool name
Description
1.
KV311039S0
Charging pipe set
2.
KV31103920*
O-ring
CVT fluid changing and adjustment
KV38107900
Protector
a:
φ 32 mm
Installing drive shaft
JSDIA1844ZZ
PDIA1183J
Tool number
Tool name
Description
31197EU50A
Drive plate location guide
a:
φ 25 mm
Installing transaxle assembly
Drift
a:
φ 56 mm
b:
φ 50 mm
Installing differential side oil seal
JPDIA0676ZZ
NT115
COMPONENT PARTS
TM-261
< SYSTEM DESCRIPTION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SYSTEM DESCRIPTION
COMPONENT PARTS
CVT CONTROL SYSTEM
CVT CONTROL SYSTEM : Component Parts Location
INFOID:0000000009268058
COMPONENT DESCRIPTION
ALDIA0266ZZ
1.
IPDM E/R
2.
TCM
3.
Transmission range switch
4.
Primary speed sensor
5.
CVT unit
6.
Output speed sensor
7.
Secondary speed sensor
8.
G sensor
9.
Stop lamp switch
10. CVT shift selector
11. Overdrive control switch
12. Combination meter (type A)
13. Combination meter (type B)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст