Nissan Versa Sedan. Manual — part 837
TM-254
< SERVICE DATA AND SPECIFICATIONS (SDS)
[4AT: RE4F03C]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000009268043
*1: Refer to
MA-12, "Fluids and Lubricants"
.
*2: The fluid capacity is the reference value.
Vehicle Speed at Which Gear Shifting Occurs
INFOID:0000000009268044
Unit: km/h (MPH)
• At half throttle, the accelerator opening is 4/8 of the full opening.
Vehicle Speed at Which Lock-up Occurs/Releases
INFOID:0000000009268045
Unit: km/h (MPH)
• At closed throttle, the accelerator opening is less than 1/8 condition. (Closed throttle position signal OFF)
• At half throttle, the accelerator opening is 4/8 of the full opening.
Stall Speed
INFOID:0000000009268046
Transaxle model
RE4F03C
Stall torque ratio
1.91 : 1
Transmission gear ratio
1st
2.861
2nd
1.562
3rd
1.000
4th
0.697
Reverse
2.310
Recommended fluid
Genuine NISSAN Matic S ATF
*1
Fluid capacity
5.2 liter (5-1/2 US qt, 4-5/8 Imp qt)
*2
CAUTION:
• Use only Genuine NISSAN Matic S ATF. Do not mix with other ATF.
• Using ATF other than Genuine NISSAN Matic S ATF will cause deterioration of driveability and A/T durability, and may dam-
age the A/T, which is not covered by the warranty.
Gear position
Throttle position
Full throttle
Half throttle
D
1
→ D
2
52 – 58 (33 – 36)
28 – 34 (18 – 21)
D
2
→ D
3
98 – 104 (61 – 64)
56 – 62 (35 – 38)
D
3
→ D
4
155 – 161 (97 – 100)
122 – 128 (76 – 79)
D
4
→ D
3
150 – 156 (94 – 96)
63 – 69 (40 – 42)
D
3
→ D
2
88 – 94 (55 – 58)
39 – 45 (25 – 27)
D
2
→ D
1
38 – 44 (24 – 27)
17 – 23 (11 – 14)
Throttle position
Gear position
Vehicle speed
Lock-up ON
Lock-up OFF
Closed throttle
3GR
33 – 39 (21 – 24)
30 – 36 (19 – 22)
4GR
52 – 58 (33 – 36)
48 – 54 (30 – 33)
Half throttle
3GR (OD OFF)
87 – 93 (55 – 57)
84 – 90 (53 – 55)
4GR
122 – 128 (76 – 79)
92 – 98 (58 – 60)
Stall speed
2,410 – 2,850 rpm
SERVICE DATA AND SPECIFICATIONS (SDS)
TM-255
< SERVICE DATA AND SPECIFICATIONS (SDS)
[4AT: RE4F03C]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Line Pressure
INFOID:0000000009268047
Unit: kPa (kg/cm2, psi)
Torque Converter
INFOID:0000000009268048
Select position
Engine speed
Line pressure
“R” position
Idle speed
570 (5.81, 82.7)
Stall speed
2,140 (21.83, 310.3)
“D” position
Idle speed
410 (4.18, 59.5)
Stall speed
1,400 (14.28, 203.0)
Dimension between end of converter housing and torque converter
16.2 mm (0.638 in)
TM-256
< PRECAUTION >
[CVT: RE0F11A]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009268049
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000009268050
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precaution for TCM and Transaxle Assembly Replacement
INFOID:0000000009268051
CAUTION:
• To replace TCM, refer to
.
• To replace transaxle assembly, refer to
Precaution for G Sensor Removal/Installation or Replacement
INFOID:0000000009268052
CAUTION:
To remove/install or replace G sensor, refer to
.
PIIB3706J
PRECAUTIONS
TM-257
< PRECAUTION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
General Precautions
INFOID:0000000009268053
• Turn ignition switch OFF and disconnect the battery cable
from the negative terminal before connecting or disconnect-
ing the CVT assembly harness connector. Because battery
voltage is applied to TCM even if ignition switch is turned
OFF.
• When connecting or disconnecting pin connectors into or
from TCM, do not damage pin terminals (bend or break).
Check that there are not any bends or breaks on TCM pin ter-
minal, when connecting pin connectors.
• Perform TCM input/output signal inspection and check
whether TCM functions normally or not before replacing TCM.
Refer to
• Perform “DTC (Diagnostic Trouble Code) CONFIRMATION
PROCEDURE”.
If the repair is completed DTC should not be displayed in the
“DTC CONFIRMATION PROCEDURE”.
• Always use the specified brand of CVT fluid. Refer to
MA-12, "Fluids and Lubricants"
• Use lint-free paper not cloth rags during work.
• Dispose of the waste oil using the methods prescribed by law, ordinance, etc. after replacing the CVT fluid.
On Board Diagnosis (OBD) System of CVT and Engine
INFOID:0000000009268054
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the
driver of a malfunction causing emission deterioration.
SEF289H
AAT470A
MEF040DA
JSBIA1315ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст