Nissan Versa Sedan. Manual — part 887
TM-454
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
TRANSMISSION ASSEMBLY
• When using suitable tool (A) for alignment, install it to the align-
ment stud bolt used to align the torque converter to the drive plate.
• Rotate the crankshaft so that the alignment hole (A) of drive plate
aligns with the position of the torque converter alignment stud bolt.
CAUTION:
• Rotate the crankshaft clockwise (as viewed from the front of
the engine).
• Be careful that torque converter stud bolts are aligned to the
drive plate holes. Otherwise the stud bolts contact the drive
plate.
• Insert the alignment stud bolt of torque converter into the align-
ment hole of the drive plate, aligning the drive plate holes with the
torque converter stud bolts.
CAUTION:
Be careful not to strike the drive plate with the torque converter stud bolts.
• When installing the torque converter nuts, temporarily tighten the nuts. Then, after installing the engine and
transaxle assembly bolts tighten the nuts to the specified torque.
CAUTION:
• Rotate the crankshaft clockwise (as viewed from the front of the engine).
• Check the tightening torque for the crankshaft pulley bolts after the bolts fastening the drive plate
and torque converter have been tightened and the crankshaft pulley bolts have been secured.
EM-47, "Removal and Installation"
• Install the transaxle assembly and engine assembly bolts accord-
ing to the following standards.
Inspection and Adjustment
INFOID:0000000009268282
INSPECTION BEFORE INSTALLATION
JPDIA0683ZZ
Tightening torque
: 51 N·m (5.2 kg-m, 38 ft-lb)
JPDIA0684ZZ
JSDIA1839ZZ
Bolt position
A
B
C
D
Direction of insertion
Transaxle assembly
⇒
Engine assembly
Engine assembly
⇒ Transaxle assembly
Quantity
2
2
1
3
Nominal length [mm (in)]
40 (1.57)
44 (1.73)
69 (2.72)
49 (1.93)
Tightening torque
N·m (kg-m, ft-lb)
48.0 (4.9, 35)
TRANSMISSION ASSEMBLY
TM-455
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Check the distance (A) between the converter housing and torque
converter.
INSPECTION AFTER INSTALLATION
Check the following items:
• For CVT position, refer to
TM-430, "Inspection and Adjustment"
• Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to
MA-12, "Fluids and Lubricants"
.
• Use procedure below to check for fuel leakage.
• Turn ignition switch ON (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leak-
age at connection points.
• Start engine. With engine speed increased, check again for fuel leakage at connection points.
• Run engine to check for unusual noise and vibration.
NOTE:
If hydraulic pressure inside timing chain tensioner drops after removal and installation, slack in the guide
may generate a pounding noise during and just after engine start. However, this is normal. Noise will stop
after hydraulic pressure rises.
• Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gas, or any oils/fluids including
engine oil and engine coolant.
• Bleed air from passages in lines and hoses, such as in cooling system.
• After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to spec-
ified level, if necessary.
• Summary of the inspection items:
*Power steering fluid, brake fluid, etc.
ADJUSTMENT AFTER INSTALLATION
• Adjust the CVT fluid level.
• Perform "ADDITIONAL SERVICE WHEN REPLACING TRANSAXLE ASSEMBLY". Refer to
B
: Scale
C
: Straightedge
Dimension (A)
:
JSDIA1840ZZ
Item
Before starting engine
Engine running
After engine stopped
Engine coolant
Level
Leakage
Level
Engine oil
Level
Leakage
Level
Transmission/
transaxle fluid
A/T and CVT Models
Leakage
Level/Leakage
Leakage
M/T Models
Level/Leakage
Leakage
Level/Leakage
Other oils and fluids*
Level
Leakage
Level
Fuel
Leakage
Leakage
Leakage
Exhaust gas
—
Leakage
—
TM-456
< SERVICE DATA AND SPECIFICATIONS (SDS)
[CVT: RE0F11A]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000009268283
*1: Refer to
MA-12, "Fluids and Lubricants"
.
*2: The CVT fluid capacity is the reference value.
Shift Characteristics
INFOID:0000000009268284
Unit: rpm
CAUTION:
Lock-up is engaged at the vehicle speed of approximately 10 km/h (11 MPH) to 90 km/h (56 MPH).
Stall Speed
INFOID:0000000009268285
Unit: rpm
Line Pressure
INFOID:0000000009268286
Unit: MPa (kg/cm
2
, psi)
Transaxle model
RE0F11A
Stall torque ratio
1.91 : 1
Pulley ratio
Forward
2.200 – 0.550
Reverse
2.200
Auxiliary gearbox gear ratio
1GR
1.821
2GR
1.000
Reverse
1.714
Counter gear
0.967
Final drive
3.882
Recommended fluid
Genuine NISSAN CVT Fluid NS-3
*1
Fluid capacity
Approx. 6.9 liter (7-1/4 US qt, 6-1/8 Imp qt)
*2
CAUTION:
• Use only Genuine NISSAN CVT Fluid NS-3. Do not mix with other fluid.
• Use only Genuine NISSAN CVT Fluid NS-3. Using transmission fluid other than Genuine NISSAN CVT Fluid NS-3 will dam-
age the CVT, which is not covered by the (NISSAN new vehicle limited) warranty.
Throttle position
Shift pattern
Engine speed
At 40 km/h (25 MPH)
At 60 km/h (37 MPH)
2/8
“D” position (Overdrive control OFF)
1,400 – 2,700
1,500 – 3,100
“D” position (Overdrive control ON)
1,500 – 2,700
2,400 – 3,200
“L” position
2,800 – 3,600
3,800 – 4,600
8/8
“D” position (Overdrive control OFF)
3,900 – 4,700
4,500 – 5,300
“D” position (Overdrive control ON)
3,900 – 4,700
4,500 – 5,300
“L” position
3,900 – 4,700
4,500 – 5,300
Stall speed
2,400 – 2,770
Shift selector position
Engine speed
Line pressure
“P” and “N”
At idle
0.50 (5.1, 72.5)
“R” and “D”
At idle
0.50 (5.1, 72.5) – 1.51 (15.4, 219)
At stall
4.93 (50.3, 714.9) – 5.43 (55.4, 787.4)
SERVICE DATA AND SPECIFICATIONS (SDS)
TM-457
< SERVICE DATA AND SPECIFICATIONS (SDS)
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Torque Converter
INFOID:0000000009268287
Heater Thermostat
INFOID:0000000009268288
Standard
Reference value
Distance (A) between the converter housing and torque converter
16.2 mm
Valve lift
More than 5.0 mm (0.197 in)
Valve opening temperature
71
°C (160°F)
Minimum valve lift
5.0 mm/85
°C (0.197 in/203°F)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст