Nissan Versa Sedan. Manual — part 443
FAX-24
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000009268304
Drive Shaft
INFOID:0000000009268305
Item
Standard
Axial end play
0.055 mm (0.002 in) or less
Rotating torque
1.9 N·m (0.19 kg-m, 17 in-lb) or less
Spring balance measurement
13.7 N (1.40 kg-f, 3.08 lb-f) or less
Application
M/T
Joint type
Wheel side
Transaxle side
LH
RH
LH
RH
Grease quantity
90 - 100 g
(3.17 - 3.53 oz)
141.1- 157.1 g
(4.98 - 5.54 oz)
Boot installed length (L)
135.5 mm (5.33 in)
154 mm (6.06 in)
Application
CVT
Joint type
Wheel side
Transaxle side
LH
RH
LH
RH
Grease quantity
90 - 100 g
(3.17 - 3.53 oz)
132.7 - 148.7 g
(4.68 - 5.25 oz)
Boot installed length (L)
136.8 mm (5.39 in)
145.5 mm (5.73 in)
Application
A/T
Joint type
Wheel side
Transaxle side
LH
RH
LH
RH
Grease quantity
90 - 100 g
(3.17 - 3.53 oz)
132.7 - 148.7 g
(4.68 - 5.25 oz)
Boot installed length (L)
136.8 mm (5.39 in)
145.5 mm (5.73 in)
ALDIA0269ZZ
ALDIA0268ZZ
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX-25
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
Dynamic Damper
INFOID:0000000009268306
Unit: mm (in)
Boot Bands
INFOID:0000000009268307
Unit: mm (in)
Application
M/T
A/T
CVT
LH
RH
LH
RH
LH
RH
Dimension (A)
240
± 3 (9.45 ±
0.1)
457
± 3 (17.99 ±
0.1)
240
± 3 (9.45 ±
0.1)
457
± 3 (17.99 ±
0.1)
242.9
± 3 (9.56 ±
0.1)
457
± 3 (17.99 ±
0.1)
Dimension (B)
70 (2.76)
70 (2.76)
70 (2.76)
ALDIA0270ZZ
Dimension (M) - maximum
7.0 (0.28)
AWDIA0598ZZ
FL-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
FL
A
FL
N
O
P
CONTENTS
FUEL SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
General Precautions . . . . . . . . . . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tools . . . . . . . . . ....
PERIODIC MAINTENANCE . . . . . . ..
FUEL SYSTEM . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
Quick Connector . . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . .
FUEL LEVEL SENSOR UNIT, FUEL FILTER
AND FUEL PUMP ASSEMBLY . . . . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
FUEL TANK . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . .
EVAP CANISTER . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
EVAP CANISTER FILTER . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
EVAP CANISTER VENT CONTROL VALVE ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
EVAP CONTROL SYSTEM PRESSURE SEN-
SOR . . . . . . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY .
FUEL LEVEL SENSOR UNIT . . . . . . ...
Disassembly and Assembly . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
FL-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009267696
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
General Precautions
INFOID:0000000009267697
WARNING:
When replacing fuel line parts, be sure to observe the following.
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
• Do not smoke while servicing fuel system. Keep open flames and sparks away from the work area.
CAUTION:
• Use gasoline required by the regulations for octane number. Refer to
GI-33, "Fuel (Regular Unleaded
.
• Before removing fuel line parts, perform the following procedures:
- Put drained fuel in an explosion-proof container and put the lid on securely. Keep the container in
safe area.
- Release fuel pressure from the fuel lines. Refer to
.
- Disconnect the battery cable from the negative terminal.
• Always replace O-ring and clamps with new ones.
• Do not kink or twist tubes when they are being installed.
• Do not tighten hose clamps excessively to avoid damaging hoses.
• After installing tubes, check there is no fuel leakage at connections in the following steps.
- Apply fuel pressure to fuel lines with turning ignition switch “ON” (with engine stopped). Then check
for fuel leakage at connections.
- Start engine and rev it up and check for fuel leakage at connections.
• Use only a Genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the
MIL may come on.
• For servicing “EVAPORATIVE EMISSION SYSTEM” parts, refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст