Nissan Versa Sedan. Manual — part 442
FAX-20
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT DRIVE SHAFT
b. Secure dynamic damper with bands in the specified position.
CAUTION:
Do not reuse bands.
2. Remove any old grease that exists on the housing.
3. Install dust shield.
CAUTION:
Do not reuse dust shield.
4. Install circlip to housing.
CAUTION:
Do not reuse circlip.
5. Install new boot and boot bands to shaft.
CAUTION:
• Wrap serration on shaft with tape (A) to protect boot from
damage.
• Do not reuse boot and boot bands.
6. Remove the tape wrapped around the serration on shaft.
7. To install the spider assembly (1), align it with the matching
marks (A) on the shaft (2) during the removal, and direct the ser-
ration mounting surface (B) to the shaft.
8. Secure spider assembly onto shaft with snap ring (1).
CAUTION:
Do not reuse snap ring.
9. Apply the appropriate amount of grease to spider assembly and
sliding surface.
10. Assemble the housing onto spider assembly, and apply the bal-
ance of the specified amount grease.
11. Align matching marks put during the removal of housing.
12. Install boot securely into grooves (indicated by “*” marks).
CAUTION:
Dimension (A)
: Refer to
JPDIF0178ZZ
JPDIF0009ZZ
JPDIF0017ZZ
Grease quantity
: Refer to
JPDIF0014ZZ
FRONT DRIVE SHAFT
FAX-21
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
If grease adheres to the boot mounting surface (with “*” mark) on shaft or housing, boot may be
removed. Remove all grease from the surface.
13. To prevent the deformation of the boot, adjust the boot installa-
tion length to the value shown below by inserting the suitable
tool into the inside of boot from the large diameter side of boot
and discharging inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may
cause breakage of the boot.
• Be careful not to touch the inside of the boot with the tip
of tool.
14. Install large and smaller boot bands securely.
CAUTION:
Do not reuse boot bands.
a. Put boot band in the groove on drive shaft boot. Then fit pawls
into holes to temporary installation.
: Pawl
NOTE:
For the large diameter side, fit projection (A) and guide slit (B) at
first.
b. Pinch projection on the band with suitable pliers to tighten band.
c. Insert the tip of band into the lower part of pawl as shown.
: Pawl
15. Check that displacement does not occur when boot is rotated
with the housing assembly fixed.
CAUTION:
• If displacement occurs, replace band.
• Do not reuse boot band.
Wheel Side
1. Clean the old grease on joint sub-assembly with paper waste.
2. Fill serration slot joint sub-assembly (1) with NISSAN genuine
grease or equivalent until the serration slot and ball groove
become full to the brim.
CAUTION:
After applying grease, use a paper waste to wipe off old
grease that has oozed out.
3. Install boot and boot bands to shaft.
CAUTION:
Boot installation
length (L)
: Refer to
JPDIF0230ZZ
JPDIF0157ZZ
JPDIF0158ZZ
JPDIF0008ZZ
FAX-22
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT DRIVE SHAFT
• Wrap serration on shaft with tape (A) to protect the boot
from damage.
• Do not reuse boot and boot band.
4. Remove the tape wrapped around the serration on shaft.
5. Position the circlip (1) on groove at the shaft edge.
CAUTION:
Do not reuse circlip.
NOTE:
Drive joint inserter is recommended when installing circular clip.
6. Align both center axles of the shaft edge and joint sub-assembly.
Then assemble shaft with joint sub-assembly holding circular
clip.
7. Install joint sub-assembly to shaft using plastic hammer.
CAUTION:
• Check circlip is properly positioned on groove of the joint
sub-assembly.
• Confirm that joint sub-assembly is correctly engaged
while rotating drive shaft.
8. Apply the specified amount of grease into the boot inside from
large diameter side of boot.
9. Install the boot securely into grooves (indicated by “*” marks).
CAUTION:
If grease adheres to the boot mounting surface (indicated by “*” mark) on the shaft or joint sub-
assembly, boot may be removed. Remove all grease from the boot mounting surface.
10. To prevent the deformation of the boot, adjust the boot installa-
tion length to the specified value shown below by inserting the
suitable tool into inside of the boot from the large diameter side
of the boot and discharging the inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may
cause breakage of the boot.
• Be careful not to touch the inside of the boot with a tip of
tool.
JPDIF0009ZZ
JPDIF0305ZZ
Grease quantity
: Refer to
.
RAC0049D
Boot installation
length (L)
: Refer to
JPDIG0136ZZ
FRONT DRIVE SHAFT
FAX-23
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
11. Secure the large and small ends of the boot with boot bands
using Tool (A).
CAUTION:
• Do not reuse boot band.
• Secure boot band so that dimension (M) meets the speci-
fication as shown.
12. Check that displacement does not occur when boot is rotated
with the joint sub-assembly and shaft.
CAUTION:
Do not reuse boot band.
Tool number : KV40107300 ( — )
JPDIF0012ZZ
Dimension (M)
.
AWDIA0598ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст