Nissan Versa Sedan. Manual — part 679
SE-42
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
9. Pull the side air bag module (1) out of the chute (A) and remove
from the seatback trim.
CAUTION:
• Replace the side air bag module if it has been dropped or
sustained an impact.
• Do not strike the side air bag module.
10. Separate the seatback trim from the seatback pad.
a. For seatback with removable headrest.
i.
Remove the hog rings and separate the seatback trim (1) from
the seatback pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
b. For seatback without removable headrest.
i.
Remove the hog rings and separate the seatback trim (1) from
the seatback pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.
• Tighten the side air bag module nuts to specification. Refer to
SE-38, "PASSENGER SIDE : Exploded View"
.
CAUTION:
Do not reuse the side air bag module nuts.
• Tighten the chute rod nuts to specification. Refer to
SE-38, "PASSENGER SIDE : Exploded View"
CAUTION:
Do not reuse the chute rod nuts.
CAUTION:
AWJIA0924ZZ
JMHIA0009ZZ
ALJIA0988ZZ
ALJIA0989ZZ
FRONT SEAT
SE-43
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Inspect seatback pad, seatback trim and seatback trim chutes. Replace if damaged.
• Smooth out all wrinkles during assembly.
• Always route side air bag module harness in original location. Replace any deformed or damaged
clips with same type and color. Always install clips in the original location in the harness.
• After work is completed, check that no system malfunction is detected causing the air bag warning
lamp to illuminate.
• If a malfunction is detected by the air bag warning lamp after repair or replacement of the malfunc-
tion parts, perform the SRS final check. Refer to
.
• Install new hog rings on the seatback trim in original positions.
Use only one hog ring in each designated location.
Ensure hog rings are correctly fastened around both the seatback
trim and seatback pad wires.
Use NISSAN standard hog rings and tools to assemble.
SEAT CUSHION
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seat cushion repair. It can lead
to personal injury if the side air bag should accidentally deploy.
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least three
minutes.
• Always work from the side or back of the seatback assembly, do not work in front of seat.
• Do not use air tools or electric tools for servicing the seat assembly.
• During disassembly, do not damage the seatback cover, chutes, connectors, retainers, clips, module
harness or the side air bag module.
Disassembly
1. Remove the front seat assembly. Refer to
SE-20, "PASSENGER SIDE : Removal and Installation"
2. Remove the recline lever.
a. Remove snap ring (1) using a suitable tool, then remove the
recline lever (2).
3. Remove the seat cushion outer finisher (RH).
PIIB3356J
AWJIA0907ZZ
SE-44
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
a. Remove the screw (A).
b. Release the metal clips and remove the seat cushion outer fin-
isher (RH).
: Metal clip
4. Remove the seat belt buckle.
a. Unclip the seat belt buckle harness clip and connector clip from seat frame assembly.
b. Remove seat belt buckle anchor bolt and the seat belt buckle.
5. Remove the seat cushion outer finisher (LH).
a. Remove seat cushion trim retainer (A) and roll up seat cushion
trim (1).
b. Remove the screw (B).
c.
Slide seat cushion outer finisher (LH) (2) rearward to release
pawl and remove.
: Pawl
6. Remove the seat cushion trim and seat cushion pad as an assembly from the seat frame assembly.
a. Remove the seatback trim lower retainer strap (A) and cushion
J-clip retainer (B).
b. Remove seat cushion trim hog rings.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
c.
Remove the seat cushion trim and seat cushion pad from seat
frame assembly.
7. Separate the seat cushion trim from the seat cushion pad.
AWJIA0917ZZ
AWJIA0918ZZ
AWJIA0919ZZ
AWJIA0923ZZ
FRONT SEAT
SE-45
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
a. Remove the hog rings and separate the seat cushion trim (1)
from the seat cushion pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.
CAUTION:
• Smooth out all wrinkles during assembly.
• Always route side air bag module harness in original location. Replace any deformed or damaged
clips with same type and color. Always install clips in the original location in the harness.
• After work is completed, check that no system malfunction is detected causing the air bag warning
lamp to illuminate.
• If a malfunction is detected by the air bag warning lamp after repair or replacement of the malfunc-
tion parts, perform the SRS final check. Refer to
.
• Install new hog rings on the seat cushion trim in original positions.
Use only one hog ring in each designated location.
Ensure hog rings are correctly fastened around both the seat cush-
ion trim and seat cushion pad wires.
Use NISSAN standard hog rings and tools to assemble.
PASSENGER SIDE : Disassembly and Assembly - Side Air Bag Module
INFOID:0000000009268535
DISASSEMBLY
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seatback repair. It can lead to
personal injury if the side air bag should accidentally deploy.
CAUTION:
• Before servicing the side air bag module, turn ignition switch OFF, disconnect both battery terminals
and wait at least three minutes.
• Handle the side air bag module carefully. During disassembly, always hold the side air bag module,
do not let it hang by the wire harness.
• Always work from the side or back of the seatback assembly, do not work in front of seat.
• Do not use air tools or electric tools for servicing the seat assembly.
• Replace the side air bag module if it has been dropped or sustained an impact.
• Do not insert any objects into the side air bag module.
• Do not attempt to disassemble the side air bag module.
• Do not expose the side air bag module to temperatures exceeding 93
°C (200°F).
• Do not expose the side air bag module to any oil, grease, detergent or water.
• During disassembly, do not damage the seatback board, chutes, connectors, retainers, clips, module
harness or the side air bag module.
NOTE:
• If the vehicle has been involved in a collision and the side air bag module has deployed, the front seatback
assembly must be replaced.
• For side air bag module removal and installation, seatback trim and seatback pad must be removed.
1. Remove the front seat assembly. Refer to
SE-20, "PASSENGER SIDE : Removal and Installation"
ALJIA0990ZZ
PIIB3356J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст