Nissan Versa Sedan. Manual — part 680
SE-46
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
2. Release the lower seatback trim retainer strap (A) from the
cushion springs.
3. Release the J-hook retainer (C), unzip seatback zipper (A) and
release J-clips (B) holding the seatback trim to the seat frame
assembly.
4. Reach up through seatback trim and release locks as shown
and remove the headrest holders (if equipped).
CAUTION:
Before removing/installing the headrest holder, check its
orientation (front/rear and right/left)
5. Remove and discard the two chute rod nuts (A), then route the
chute rod (1) through the opening and remove it from the chute
(B).
CAUTION:
Do not reuse the chute rod nuts.
6. Release the side air bag module harness from seat frame
assembly.
NOTE:
Take note of harness routing and attachment location for accu-
rate installation.
a. From the back of the seat unclip the side air bag module har-
ness clips (
).
AWJIA0913ZZ
AWJIA0914ZZ
PIIB4084J
AWJIA0922ZZ
AWJIA0915ZZ
FRONT SEAT
SE-47
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
7. Remove and discard the two side air bag module nuts (A).
CAUTION:
Do not reuse the side air bag module nuts.
8. Disengage the side air bag module studs from the seatback frame and lift the seatback trim and seatback
pad as an assembly from the seat frame assembly.
9. Pull the side air bag module (1) out of the chute (A) and remove
from the seatback trim.
CAUTION:
• Replace the side air bag module if it has been dropped or
sustained an impact.
• Do not strike the side air bag module.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Tighten the side air bag module nuts to specification. Refer to
SE-38, "PASSENGER SIDE : Exploded View"
.
CAUTION:
Do not reuse the side air bag module nuts.
• Tighten the chute rod nuts to specification. Refer to
SE-38, "PASSENGER SIDE : Exploded View"
.
CAUTION:
Do not reuse the chute rod nuts.
CAUTION:
• Inspect seatback pad, seatback trim and seatback trim chutes. Replace if damaged.
• Smooth out all wrinkles during assembly.
• Always route side air bag module harness in original location. Replace any deformed or damaged
clips with same type and color. Always install clips in the original location in the harness.
• After work is completed, check that no system malfunction is detected causing the air bag warning
lamp to illuminate.
• If a malfunction is detected by the air bag warning lamp after repair or replacement of the malfunc-
tion parts, perform the SRS final check. Refer to
.
AWJIA0916ZZ
AWJIA0924ZZ
JMHIA0009ZZ
SE-48
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR SEAT
REAR SEAT
Exploded View - Fixed Seatback
INFOID:0000000009268536
FIXED SEATBACK
ALJIA0982ZZ
1.
Headrest holder (locked)
2.
Headrest holder (free)
3.
Rear seatback assembly
4.
Seatback trim
5.
Seatback pad
6.
LATCH bracket (RH)
7.
Seat cushion assembly
8.
Seat cushion trim
9.
Seat cushion pad
10. Seat cushion hook
11. LATCH bracket (LH)
12. Headrest
REAR SEAT
SE-49
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Exploded View - 60:40 Split Seatback
INFOID:0000000009268537
60:40 SPLIT SEATBACK
ALJIA0981ZZ
1.
Headrest
2.
Rear seatback assembly (RH)
3.
Headrest holder (free)
4.
Headrest holder (locked)
5.
Rear seatback frame (RH)
6.
Seatback latch assembly (RH)
7.
Seatback trim (RH)
8.
Seatback pad (RH)
9.
Rear seat bolster (RH)
10. Seatback hinge finisher
11. Seat cushion assembly
12. Seat cushion trim
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст