Nissan Almera Tino V10 (2001 year). Manual — part 120
3
CHECK DRIVER SIDE DOOR SWITCH
Check continuity between terminals 2 and 3.
NEL648
OK or NG
OK
©
Check the following.
+
Driver side door switch ground circuit and condition
+
Harness for open or short between time control unit and driver side door switch
NG
©
Replace driver side door switch.
WARNING CHIME
Trouble Diagnoses (Cont’d)
EL-175
System Description
NLEL0456
WIPER OPERATION
NLEL0456S01
The wiper switch is controlled by a lever built into the combination switch.
There are three wiper switch positions:
+
LO speed
+
HI speed
+
INT (Intermittent)
Power is supplied at all time
+
through 30A fuse
+
to front wiper relay-1 terminal 5, and
+
through 40A fusible link
+
through ignition switch terminal 1 and 3 when the switch is in the ON or START position
+
to front wiper relay-1 terminal 1.
Ground is supplied
+
to front wiper relay-1 terminal 2
+
through body grounds E24 and E73
With power and ground supplied, the front wiper relay-1 is energized.
Low and High Speed Wiper Operation
NLEL0456S0101
Ground is supplied to wiper and washer switch terminal 17 through body grounds E30 and E73.
When the wiper switch is placed in the LO position, ground is supplied
+
through terminal 14 of the front wiper and washer switch
+
to front wiper motor terminal 4.
With power and ground supplied, the wiper motor operates at low speed.
When the wiper switch is placed in the HI position, ground is supplied
+
through terminal 16 of the front wiper and washer switch
+
to wiper motor terminal 5.
With power and ground supplied, the wiper motor operates at high speed.
Auto Stop Operation
NLEL0456S0102
With wiper switch turned OFF, wiper motor will continue to operate until wiper arms reach windshield base.
When wiper arms are not located at base of windshield with wiper switch OFF, ground is provided
+
from terminal 14 of the front wiper and washer switch
+
to front wiper motor terminal 4, in order to continue wiper motor operation at low speed.
Ground is also supplied
+
through terminal 13 of the front wiper and washer switch
+
to front wiper relay-2 terminal 3
+
through terminal 4 of the front wiper relay-2.
+
to front wiper motor terminal 2
+
through terminal 3 of front wiper motor
+
through body grounds E24 and E73.
When wiper arms reach base of windshield, front wiper motor terminals 2 and 3 are connected instead of ter-
minals 2 and 1. Wiper motor will then stop wiper arms at the STOP position.
Intermittent Operation
NLEL0456S0103
The front wiper motor operates the wiper arms one time at low speed at a set interval of approximately 1 to
13 seconds. This feature is controlled by the wiper amplifier (INT SW) combined with front wiper switch.
When the wiper switch is placed in the INT position, ground is supplied to wiper amplifier (WIPER SW INT)
and (ACC).
The desired interval time is input to wiper amplifier (INT VR) from wiper volume switch combined with front
wiper and washer switch.
Then intermittent ground is supplied
+
from body grounds E24 and E73
+
through terminal 5 of front wiper relay-2,
+
through terminal 3 of front wiper relay-2,
FRONT WIPER AND WASHER
System Description
EL-176
+
through terminal 13 of front wiper switch and,
+
through terminal 14 of front wiper switch
+
to terminal 4 of front wiper motor.
The desired interval time is input
+
to front wiper relay-2 terminal 1
+
from terminal 20 of front wiper switch
WASHER OPERATION
NLEL0456S02
With the ignition switch in the ON or START position and the lever is pulled to the WASH/F position, power
is supplied
+
through 10A fuse [No. 27, located in the fuse block (J/B)]
+
to front wiper switch terminal 5.
+
through front wiper switch terminal 3
+
to front washer motor terminal 1.
When the lever is pulled to the WASH/F position, ground is supplied
+
from body grounds E24 and E73
+
through terminal 4 of the front wiper switch
+
through terminal 18 of the front wiper switch
+
to front washer motor terminal 2.
With power and ground supplied, the washer motor operates.
When the lever is pulled to the WASH position for one second or more, the wiper motor operates at low speed
for approximately 3 seconds to clean windshield. This feature is controlled by the wiper amplifier in the same
manner as the intermittent operation.
FRONT WIPER AND WASHER
System Description (Cont’d)
EL-177
Wiring Diagram — WIPER —
NLEL0457
MODELS WITH FUSE AND FUSIBLE LINK BOX E43
NLEL0457S01
YEL903B
FRONT WIPER AND WASHER
Wiring Diagram — WIPER —
EL-178
YEL904B
FRONT WIPER AND WASHER
Wiring Diagram — WIPER — (Cont’d)
EL-179
MODELS WITH FUSE AND FUSIBLE LINK BOX E90
NLEL0457S02
YEL427C
FRONT WIPER AND WASHER
Wiring Diagram — WIPER — (Cont’d)
EL-180
YEL428C
FRONT WIPER AND WASHER
Wiring Diagram — WIPER — (Cont’d)
EL-181
SEL543TA
Removal and Installation
NLEL0060
WIPER ARMS
NLEL0060S01
1.
Prior to wiper arm installation, turn on wiper switch to operate
wiper motor and then turn it “OFF” (Auto Stop).
2.
Lift the blade up and then set it down onto glass surface to set
the blade center to clearance “L
1
” & “L
2
” immediately before
tightening nut.
3.
Eject washer fluid. Turn on wiper switch to operate wiper motor
and then turn it “OFF”.
4.
Ensure that wiper blades stop within clearance “L
1
” & “L
2
”.
Clearance “L
1
”: 20.4 - 34.4 mm (0.803 - 1.354 in)
Clearance “L
2
”: 61.8 - 75.8 mm (2.433 - 2.984 in)
+
Tighten wiper arm nuts to specified torque.
Front wiper: 21 - 26 N·m (2.1 - 2.7 kg-m, 16 - 19 ft-lb)
SEL024J
+
Before reinstalling wiper arm, clean up the pivot area as
illustrated. This will reduce possibility of wiper arm loose-
ness.
WIPER LINKAGE
NLEL0060S02
NEL719
FRONT WIPER AND WASHER
Removal and Installation
EL-182
Removal
NLEL0060S0201
1.
Remove wiper arms and cowl top cover.
2.
Remove wiper motor connector.
3.
Remove 5 screws and 3 nuts.
4.
Remove wiper linkage.
Be careful not to break ball joint rubber boot.
Installation
NLEL0060S0202
+
Grease ball joint portion before installation.
1.
Installation is the reverse order of removal.
GEL013-A
Washer Nozzle Adjustment
NLEL0061
+
Adjust washer nozzle with suitable tool as shown in the figure
at left.
Adjustable range:
±
10° (In any direction)
NEL720
Unit: mm (in)
*1
646.9 (25.47)
*5
230.1 (9.06)
*2
470.2 (18.51)
*6
16.8 (0.66)
*3
332.9 (13.11)
*7
356.5 (14.04)
*4
550.9 (21.69)
*8
394.8 (15.54)
*: The diameters of these circles are less than 80 mm (3.15 in).
Washer Tube Layout
NLEL0062
NEL725
FRONT WIPER AND WASHER
Removal and Installation (Cont’d)
EL-183
Wiring Diagram — WIP/R —
NLEL0458
MODELS WITH INTERMITTENT REAR WIPER
NLEL0458S01
YEL905B
REAR WIPER AND WASHER
Wiring Diagram — WIP/R —
EL-184
YEL906B
REAR WIPER AND WASHER
Wiring Diagram — WIP/R — (Cont’d)
EL-185
MODELS WITHOUT INTERMITTENT REAR WIPER
NLEL0458S02
YEL429C
REAR WIPER AND WASHER
Wiring Diagram — WIP/R — (Cont’d)
EL-186
YEL906B
REAR WIPER AND WASHER
Wiring Diagram — WIP/R — (Cont’d)
EL-187
NEL722
Removal and Installation
NLEL0301
WIPER ARMS
NLEL0301S01
1.
Prior to wiper arm installation, turn on wiper switch to operate
wiper motor and then turn it “OFF” (Auto Stop).
2.
Lift the blade up and then set it down onto glass surface. Set
the black center to clearance “E” immediately before tighten-
ing the nut.
3.
Eject washer fluid. Turn on wiper switch to operate wiper motor
and then turn it “OFF”.
4.
Ensure that wiper blades stop on the lowest heat wire.
+
Tighten windshield wiper arm nuts to specified torque.
: 12.7 - 17.6 N·m (1.3 - 1.8 kg-m, 10 - 13 ft-lb)
SEL024J
+
Before reinstalling wiper arm, clean up the pivot area as
illustrated. This will reduce possibility of wiper arm loose-
ness.
NEL721
Washer Nozzle Adjustment
NLEL0302
The diameter of the washer spit circle is less than 30 mm (1.18 in).
REAR WIPER AND WASHER
Removal and Installation
EL-188
Washer Tube Layout
NLEL0303
NEL723
REAR WIPER AND WASHER
Washer Tube Layout
EL-189
Wiring Diagram — HLC —
NLEL0459
MODELS WITH FUSE AND FUSIBLE LINK BOX E43
NLEL0459S01
YEL907B
HEADLAMP WASHER
Wiring Diagram — HLC —
EL-190
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст