Nissan Primera P11. Manual — part 331
WIPER LINKAGE
* Structure is basically the opposite for RHD models.
Removal
1. Remove 4 bolts that secure wiper motor.
2. Detach wiper motor from wiper linkage at ball joint.
3. Remove wiper linkage.
Be careful not to break ball joint rubber boot.
Installation
●
Grease ball joint area before installation.
1. Installation is the reverse order of removal.
MEL664DA
LHD models*
3.8 - 5.1 (0.39 - 0.52, 33.9 - 45.1)
3.8 - 5.1 (0.39 - 0.52, 33.9 - 45.1)
: N·m (kg-m, in-lb)
FRONT WIPER AND WASHER
Removal and Installation (Cont’d)
EL-191
Front Washer Nozzle Adjustment
●
Adjust washer nozzle with suitable tool as shown in the fig-
ure at left.
Adjustable range: ±10° (In any direction)
Unit: mm (in)
*1
375 (14.76)
*5
115 (4.53)
*2
160 (6.30)
*6
190 (7.48)
*3
440 (17.32)
*7
320 (12.60)
*4
100 (3.94)
*8
450 (17.72)
Circle diameters are approx. 80 mm (3.15 in).
Front Washer Tube Layout
GEL013
Suitable tool
Max.
10°
Nozzle hole
bore diameter
0.8 mm (0.031 in)
NEL311
RHD models
Black
printed edge
LHD models
Black
printed edge
Front washer
Front washer tube
Front washer nozzle
Washer tank
To rear washer
NEL312
FRONT WIPER AND WASHER
EL-192
System Description
WIPER OPERATION
The rear wiper switch and rear intermittent wiper control is built into the combination switch.
There are two rear wiper switch positions:
●
ON (LO speed)
●
INT (Intermittent).
With the ignition switch in the ON or START position, power is supplied
●
through 15A fuse (No.
18
, located in the fuse block)
●
to rear wiper motor terminal
쑗
3
(Sedan and H/B);
쑗
4
(Wagon), and
●
to rear wiper relay terminal
쑗
2
.
Low speed wiper operation
Ground is supplied to rear wiper switch terminal
쑗
4
through body grounds
E37
and
E11
.
When the rear wiper is placed in the ON position, ground is supplied
●
through rear wiper switch terminal
쑗
2
●
to rear wiper relay terminal
쑗
1
.
The rear wiper relay is energized and power is supplied
●
through 15A fuse (No.
18
, located in the fuse block)
●
to rear wiper relay terminal
쑗
5
●
through rear wiper relay terminal
쑗
3
●
to rear wiper motor terminal
쑗
2
.
Ground is supplied
●
to rear wiper motor terminal
쑗
1
(sedan and H/B);
쑗
3
(Wagon)
●
through body grounds
B18
and
B27
(Sedan);
D110
and
B48
(H/B and Wagon).
Auto stop operation
With the rear wiper switch turned OFF, rear wiper motor will continue to operate until wiper arm reaches rear
window base.
When wiper arm is not located at base of rear window with rear wiper switch OFF, rear wiper relay is not
energized.
Power is supplied
●
through 15A fuse (No.
18
, located in the fuse block)
●
to rear wiper motor terminal
쑗
3
(Sedan and H/B);
쑗
4
(Wagon).
Ground is also supplied
●
to rear wiper motor terminal
쑗
1
(Sedan and H/B);
쑗
3
(Wagon)
●
through body grounds
B18
and
B27
(Sedan);
D110
and
B48
(H/B and Wagon).
When wiper arm reaches base of rear window, rear wiper motor will then stop wiper arm at the PARK posi-
tion.
Intermittent operation
The rear wiper motor operates the wiper arm one time at low speed at an interval of approximately 7 sec-
onds. This feature is controlled by the rear wiper amplifier.
With the ignition switch in the ON or START position, power is supplied
●
through 15A fuse (No.
18
, located in the fuse block)
●
to rear wiper relay terminal
쑗
2
.
When the rear wiper is placed in the INT position, ground is supplied
●
to rear wiper relay terminal
쑗
1
●
through rear wiper switch terminal
쑗
2
●
to rear wiper amplifier
●
from rear wiper switch terminal
쑗
4
●
through bogy grounds
E37
and
E11
.
When the rear wiper relay is energized, power is supplied
●
through 15A fuse (No.
18
, located in the fuse block)
●
to rear wiper relay terminal
쑗
5
●
through rear wiper relay terminal
쑗
3
●
to rear wiper motor terminal
쑗
2
.
REAR WIPER AND WASHER
EL-193
Ground is also supplied
●
to rear wiper motor terminal
쑗
1
(Sedan and H/B);
쑗
3
(Wagon)
●
through body grounds
B18
and
B27
(Sedan);
D110
and
B48
(H/B and Wagon).
With power and ground supplied, the rear wiper motor operates intermittently.
WASHER OPERATION
With the ignition switch in the ON or START position, power is supplied
●
through 10A fuse (No.
21
, located in the fuse block)
●
to rear washer switch connector terminal
쑗
5
.
When the rear washer switch is pushed to the WASH/R position, ground is supplied
●
to rear washer motor terminal
쑗
1
●
●
from terminal
쑗
3
of rear wiper switch
●
through terminal
쑗
4
of rear wiper switch, and
●
through body grounds
E37
and
E11
.
Power is supplied
●
from terminal
쑗
18
of the washer switch
●
to washer motor terminal
쑗
2
.
With power and ground is supplied, the rear washer motor operates.
The rear wiper motor operates when the control switch is pushed to WASH position for one second or more
and for approximately 3 seconds after the switch is released. This feature is controlled by the rear wiper
amplifier in the same manner as the intermittent operation.
REAR WIPER AND WASHER
System Description (Cont’d)
EL-194
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст