Nissan Primera P11. Manual — part 460
Garage Jack and Safety Stand
WARNING:
●
Never get under the vehicle while it is supported only by the jack. Always use safety stands when
you have to get under the vehicle.
●
Place wheel chocks at both front and back of the wheels on the ground.
NGI021
Garage jack points
Safety stand points
Note:
Safety stand
points are the
same as
pantograph
jack points.
Use safety stand
adapter as shown
for stable support.
Attachment
SST No. LM4519-0000
Safety stand
Fit the lower side
sill into groove.
LIFTING POINTS AND TOW TRUCK TOWING
GI-47
2-pole Lift
WARNING:
When lifting the vehicle, open the lift arms as wide as possible and ensure that the front and rear of
the vehicle are well balanced.
When setting the lift arm, do not allow the arm to contact the brake tubes and fuel lines.
NGI022
Note:
Lift-up points are
the same as panto-
graph jack points.
Sill
Lift pad
Put the sill in the groove of the lift pad to prevent the
sill from deforming. If the pad does not have a groove,
prepare a suitable attachment with one.
LIFTING POINTS AND TOW TRUCK TOWING
GI-48
Tow Truck Towing
CAUTION:
●
All applicable local laws regarding the towing operation
must be obeyed.
●
It is necessary to use proper towing equipment to avoid
possible damage to the vehicle during towing operation.
Towing is in accordance with Towing Procedure Manual
at dealer.
●
When towing with the rear wheels on the ground, release
the parking brake and move the gearshift lever to neu-
tral position.
NISSAN recommends that vehicle be towed with the driving
(front) wheels off the ground as illustrated.
TOWING A H
⋅
CVT MODEL WITH FOUR WHEELS ON
GROUND
Observe the following restricted towing speeds and distances.
Speed:
Below 50 km/h (30 mph)
Distance:
Less than 65 km (40 miles)
CAUTION:
Never tow a H
⋅
CVT model from the rear (i.e., backward) with
four wheels on the ground as this may cause serious and
expensive damage to the transaxle.
TOWING A H
⋅
CVT MODEL WITH REAR WHEELS
RAISED (With front wheels on ground)
Never tow a H
⋅
CVT model with rear wheels raised (with front
wheels on ground) as this may cause serious and expensive
damage to the transaxle. If it is necessary to tow it with rear
wheels raised, always use a towing dolly under the front wheels.
TOWING POINT
Always pull the cable straight out from the vehicle. Never
pull on the hook at a sideways angle.
CAUTION:
Remove the front spoiler when towing the vehicle forward.
Otherwise, the towing device may damage the front spoiler.
SGI805
SGI806-A
H
⋅
CVT model
NGI049
Towing hook
Removable towing hook
LIFTING POINTS AND TOW TRUCK TOWING
GI-49
Grade
Bolt size
Bolt
diameter*
mm
Pitch
mm
Tightening torque (Without lubricant)
Hexagon head bolt
Hexagon flange bolt
N·m
kg-m
ft-lb
in-lb
N·m
kg-m
ft-lb
in-lb
4T
M6
6.0
1.0
5.1
0.52
3.8
45.1
6.1
0.62
4.5
53.8
M8
8.0
1.25
13
1.3
9
—
15
1.5
11
—
1.0
13
1.3
9
—
16
1.6
12
—
M10
10.0
1.5
25
2.5
18
—
29
3.0
22
—
1.25
25
2.6
19
—
30
3.1
22
—
M12
12.0
1.75
42
4.3
31
—
51
5.2
38
—
1.25
46
4.7
34
—
56
5.7
41
—
M14
14.0
1.5
74
7.5
54
—
88
9.0
65
—
7T
M6
6.0
1.0
8.4
0.86
6.2
74.6
10
1.0
7
87
M8
8.0
1.25
21
2.1
15
—
25
2.5
18
—
1.0
22
2.2
16
—
26
2.7
20
—
M10
10.0
1.5
41
4.2
30
—
48
4.9
35
—
1.25
43
4.4
32
—
51
5.2
38
—
M12
12.0
1.75
71
7.2
52
—
84
8.6
62
—
1.25
77
7.9
57
—
92
9.4
68
—
M14
14.0
1.5
127
13.0
94
—
147
15.0
108
—
9T
M6
6.0
1.0
12
1.2
9
—
15
1.5
11
—
M8
8.0
1.25
29
3.0
22
—
35
3.6
26
—
1.0
31
3.2
23
—
37
3.8
27
—
M10
10.0
1.5
59
6.0
43
—
70
7.1
51
—
1.25
62
6.3
46
—
74
7.5
54
—
M12
12.0
1.75
98
10.0
72
—
118
12.0
87
—
1.25
108
11.0
80
—
137
14.0
101
—
M14
14.0
1.5
177
18.0
130
—
206
21.0
152
—
1. Special parts are excluded.
2. This standard is applicable to bolts having the following
marks embossed on the bolt head.
*: Nominal diameter
Grade
Mark
4T
. . .
4
M
6
7T
. . .
7
üüüNominal diameter of bolt threads (Unit: mm)
9T
. . .
9
üüüMetric screw threads
TIGHTENING TORQUE OF STANDARD BOLTS
GI-50
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст