Nissan Primera P11. Manual — part 508
NCMT0003
NVH
T
roubleshooting
Chart
NCMT0003S01
Use
the
chart
below
to
help
you
find
the
cause
of
the
symptom.
The
numbers
indicate
the
order
of
the
inspec-
tion.
If
necessary
,
repair
or
replace
these
parts.
Reference
page
Refer to MA section (“Checking
M/T Oil”, “CHASSIS AND BODY
MAINTENANCE”).
SUSPECTED
P
A
R
T
S
(Possible
cause)
(Oil level is low.)
(Wrong oil)
(Oil level is high.)
GASKET (Damaged)
OIL SEAL (Worn or damaged)
O-RING (Worn or damaged)
CONTROL ROD (Worn)
CHECK PLUG RETURN SPRING AND CHECK BALL (Worn or damaged)
SHIFT FORK (Worn)
GEAR (Worn or damaged)
BEARING (Worn or damaged)
BAULK RING (Worn or damaged)
INSERT SPRING, SHIFTING INSERT (Damaged)
Symptom
Noise
1
2
3
3
Oil
leakage
31222
Hard
to
shift
or
will
not
shift
1
1
2
3
3
Jumps
out
of
gear
1233
NOISE,
V
IBRATION
AND
HARSHNESS
(NVH)
T
ROUBLESHOOTING
NVH
T
roubleshooting
Chart
MT-7
Replacing Oil Seal
NCMT0005
DIFFERENTIAL OIL SEAL
NCMT0005S01
1.
Drain gear oil from transaxle.
2.
Remove drive shafts — Refer to section FA.
3.
Remove differential oil seal.
4.
Install differential oil seal.
I
Apply multi-purpose grease to seal lip of oil seal before
installing.
5.
Install drive shafts — Refer to section FA.
I
Install differential oil seal so that dimension “A” and “B”
are within specifications.
Unit: mm (in)
Item
A
B
F32A
5.9 - 6.1 (0.232 - 0.240)
0.5 (0.020) or less
F70A
0.5 (0.020) or less
STRIKING ROD OIL SEAL
NCMT0005S02
1.
Remove transaxle control rod from yoke.
2.
Remove retaining pin of yoke.
I
Be careful not to damage boot.
SMT563A
ST33290001
SMT564AB
Drift
.
Drift: LH side ST33400001 (F31A)
KV31103000 and ST35325000 (F32A
& F32V) RH side ST30720000 (F31A)
LH and RH side KV38100200 (F70A)
SMT738B
F32A
Transmission
case side
Clutch housing side
Oil seal
SMT869D
Transaxle case side
Clutch housing side
Differential oil seal
Differential oil seal
F70A
SMT565A
KV32101000
ON-VEHICLE SERVICE
Replacing Oil Seal
MT-8
3.
Remove striking rod oil seal.
4.
Install striking rod oil seal.
I
Apply multi-purpose grease to seal lip of oil seal before
installing.
Position Switch Check
NCMT0006
BACK-UP LAMP SWITCH
NCMT0006S01
I
Check continuity
Gear Position
Continuity
Reverse
Yes
Except reverse
No
NEUTRAL POSITION SWITCH
NCMT0006S02
I
Check continuity.
Gear position
Continuity
Neutral
Yes
Except neutral
No
SMT566A
Drift
SMT570A
Drift
SMT715B
Back-up lamp
switch harness
connector
Neutral position
switch connector
F31A and F32A
NMT090
Back-up lamp
switch harness
connector
Neutral position
switch harness
connector
F70A
ON-VEHICLE SERVICE
Replacing Oil Seal (Cont’d)
MT-9
Removal
NCMT0007S01
1.
Remove battery negative terminal.
2.
Remove air duct.
3.
Disconnect clutch control cable from transaxle (GA16 models).
4.
Remove clutch operating cylinder from transaxle (except GA16
models).
5.
Disconnect back-up lamp switch, speedometer sensor, neutral
position switch and ground harness connectors.
6.
Remove starter motor from transaxle.
7.
Remove shift control rod and support rod from transaxle.
8.
Drain gear oil from transaxle.
9.
Remove exhaust front tube.
10. Draw out drive shafts from transaxle — Refer to section FA.
.
SMT653B
Front
SMT654B
.
Starter motor
Front
SMT655B
Shift control rod
Shift support rod
.
F31A and F32A
NMT091
.
Control rod
.
Support rod
.
F70A
SMT656B
Knuckle
spindle
upper nut
Drive shaft
REMOVAL AND INSTALLATION
Removal
MT-10
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст