Nissan Primera P11. Manual — part 65
NBT057
Type 2
SEC. 880
Rear seat back striker (RH)
Rear seat back striker (LH)
Rear seat side back hinge
Rear seat hinge
Rear seat hook
Rear seat back hinge
12.7 - 15.7
(1.3 - 1.6,
9.4 - 11.6)
12.7 - 15.7
(1.3 - 1.6, 9.4 - 11.6)
12.7 - 15.7
(1.3 - 1.6,
9.4 - 11.6)
43.1 - 54.8
(4.4 - 5.5,
32 - 40)
43.1 - 54.8
(4.4 - 5.5,
32 - 40)
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
Tightening sequence
A: Finger
tight
B: 43.1 - 54.8
(4.4 - 5.5,
32 - 40)
C: 43.1 - 54.8
(4.4 - 5.5,
32 - 40)
A, C
B
5.1 - 6.47 (0.52 - 0.66, 45.1 - 57.3)
.
SEAT
Rear Seat (Cont’d)
BT-45
ADJUSTMENT
Install motor & limit SW assembly and sunroof rail assembly in the following sequence:
1. Arrange equal lengths of link and wire assemblies on both sides of sunroof opening.
2. Connect sunroof connector to sunroof switch and positive (+) power supply.
3. Set lid assembly to fully closed position
by operating open/tilt sunroof switch.
4. Fit outer side of lid assembly to the surface of roof on body outer panel.
5. Remove motor, and keep sunroof switch pressed to rear side until motor pinion gear reaches the end
of its rotating range.
6. Install motor.
7. Check that motor drive gear fits properly in wires.
8. Press front side of sunroof switch to check lid assembly for normal tilting.
9. Check sunroof lid assembly for normal operations (tilt-up, tilt-down, open, and close).
SBF920F
Front
Lid assembly
Closing & opening range
Rear
Tilting up & down range
Outer body panel
Closing & opening range
SUNROOF
BT-46
REMOVAL
●
After any adjustment, check sunroof operation and lid alignment.
●
Handle finisher plate and glass lid with care so not to cause damage.
●
It is desirable for easy installation to mark each point before removal.
CAUTION:
Always work with a helper.
Link and wire
assembly
Sunroof frame
assembly
Shade assembly
Lid assembly
Motor assembly
Tilt glass lid up.
p
1
Sunroof lid mount screws
p
2
Lid assembly
p
3
Rear drain mount screws
p
4
Rear drain assembly
Operate sunroof switch to tilt glass lid down.
p
5
Shade assembly
Sunroof switch/interior accessories/headlining (Models equipped with sunroof)
●
Refer to “Roof Trim” in “INTERIOR TRIM” for details, BT-25, BT-26, BT-27.
p
6
Motor switch bracket
p
7
Motor assembly
p
8
Wind deflector mount nuts
p
9
Wind deflector mount screws
p
10
Wind deflector assembly
p
11
Drain hoses
p
12
Sunroof unit bracket
p
13
Sunroof frame assembly
p
14
Guide stopper
p
15
Link and wire assembly
SUNROOF
BT-47
★
For Wiring Diagram, refer to “ELECTRIC SUNROOF” in EL section.
NBT049
SEC. 736
Rear drain
assembly
Rear drain screw
Link and wire
assembly
Guide stopper
Wind deflector mounting nuts
Drain hose
Sunroof unit bracket
5.1 - 6.4
(0.52 - 0.65,
45.1 - 56.4)
Motor
switch bracket
Motor assembly
5.1 - 6.4
(0.52 - 0.65,
45.1 - 56.4)
Sunroof frame
assembly
Wind
deflector
assembly
Wind deflector mounting
screws
Shade assembly
Guide stopper
Screw
: N·m (kg-m, in-lb)
Lid assembly
Manual type
Drive
Handle
: Apply grease
SUNROOF
BT-48
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст