Nissan Primera P11. Manual — part 66
Using flat-bladed screwdriver, pry shade assembly holder off
rail. Then pull shade assembly forward to remove it from rail.
Trouble Diagnoses
DIAGNOSTIC TABLE
NOTE: For diagnosing electric problem, refer to “ELECTRIC SUNROOF” in EL section.
Check item (Components)
Wind deflector
Adjustment
Drain hoses
Weatherstrip
Link and wire
assembly
Reference page
Symptom
Excessive wind
noise
1
2
3
Water leaks
1
2
3
Sunroof rattles
1
4
2
3
Excessive
operation noise
1
2
3
The numbers in this table mean checking order.
WIND DEFLECTOR
1. Open lid
2. Check visually for proper installation.
3. Check to ensure a proper amount of petroleum jelly has been
applied to wind deflector connection points; apply if neces-
sary.
4. Check that wind deflector is properly retracted by hand. If it
is not, remove and visually check condition. (Refer to
removal procedures, BT-47). If wind deflector is damage,
replace with new one. If wind deflector is not damage, re-in-
stall properly.
YBT060
Shade holder
Rail
Front
Shade ASSY
Holder
SBT331
Roof panel
Wind reflector arm
Wind reflector
SBT332
Roof
panel
Wind reflector arm
Wind reflector
SUNROOF
BT-49
ADJUSTMENT
If any gap or height differences between lid and roof is found,
check lid and adjust as follows:
Gap Adjustment
1. Remove shade assembly. (Refer to removal procedures
BT-47, for details).
2. Tilt lid up.
3. Loosen lid securing nuts (3 each on left and right sides), then
tilt lid down.
4. Adjust lid from outside of vehicle so it resembles “A-A” as
shown in the figure above.
5. Tilt lid up and down until it is adjusted to “B-B” as shown in
the figure above.
6. After adjusting lid, tilt lid up and tighten nuts.
7. Tilt lid up and down several times to check that it moves
smoothly.
Height difference adjustment
1. Tilt lid up and down.
2. Check height difference between roof panel and lid to see if
it is as “A-A” as shown in the figure above.
3. If necessary, adjust it by using one of following procedures:
●
Adjust by adding or removing adjustments shim(s) between
lid and link assembly.
●
If lid protrudes above roof panel, add shim(s) or plain wash-
er(s) at sunroof mounting bracket or stud bolt locations to
adjust sunroof installation as required.
SBT381
Unit: mm (in)
Roof
panel
5.4 - 6.3 (0.213 - 0.248)
0.7 ± 0.028 ± 0.039
12
+1.2
-2.0
(0.47
+0.047
-0.079
)
Lid
Lid
33.1 ± 5
(1.303 ± 0.197)
Roof
panel
SEC. 736
SUNROOF
Trouble Diagnoses (Cont’d)
BT-50
DRAIN HOSES
1. Remove headlining to access drain hose connections. (Refer
to “REMOVAL — Headlining” in “INTERIOR TRIM”, BT-25,
BT-26, BT-27 for detail).
2. Check visually for proper connections, damage or deteriora-
tion.
(The figure shows only the front side.)
3. If leakage occur around trunk room, remove trunk room side
trim
and
check
connecting
area.
Check
for
proper
connection, damage or tear.
4. Pour water into drain hoses and find damaged portion.
●
If any damaged portion is found at each step, replace the
damaged part.
WEATHERSTRIP
●
In the case of leakage around lid, close lid and pour water
over lid to find damaged or gap portion.
1. Remove lid assembly. (Refer to removal procedures, BT-47,
for details).
2. Visually check weatherstrip for proper installation. If a gap
exists between lid and weatherstrip, check for sufficient
amount of butyl seal. If required, remove weatherstrip and
apply butyl seal.
Refer to “EXTERIOR” BT-31 for details.
SBT335
Drain hose
SBT333
Sunroof frame
assembly
Drain hose
SBT334
.
Sunroof drain
hose
Front
Grommet
Rear wheel
house inner LH
Rear fender inner LH
SUNROOF
Trouble Diagnoses (Cont’d)
BT-51
3. Check weatherstrip visually for damage, deterioration, or flat-
tening.
●
If any damage is found, replace weatherstrip.
CAUTION:
Do not remove weatherstrip except when replacing, or fill-
ing up butyl seal.
LINK AND WIRE ASSEMBLY
Before replacing a suspect part, carefully ensure it is the
source of noise being experienced.
1. Check link to determine if coating film has been peeled of to
such an extent that substrate is visible. Check also to deter-
mine if link is the source of noise. If it is, replace it.
2. Visually check to determine if a sufficient amount of petro-
leum jelly has been applied to wire or rail groove. If not, add
petroleum jelly as required.
3. Check wire for any damage or deterioration. If any damage
is found, remove rear guide (refer to removal procedures,
BT-47 for details), then replace wire.
SUNROOF
Trouble Diagnoses (Cont’d)
BT-52
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст