Qashqai J11. Road wheels & tires — part 4
LOW TIRE PRESSURE LOCATION INDICATOR CONTINUES DISPLAYING
WT-53
< SYMPTOM DIAGNOSIS >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE LOCATION INDICATOR CONTINUES DISPLAYING
Description
INFOID:0000000010339561
The low tire pressure location indicator continues displaying though low tire pressure warning lamp turns/stays
OFF.
Diagnosis Procedure
INFOID:0000000010339562
1.
CHECK TIRE PRESSURE
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
3.
Perform TPMS temperature calibration. Refer to
WT-14, "TPMS temperature calibration"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels.
2.
CHECK LOW TIRE PRESSURE LOCATION INDICATOR
Check low tire pressure location indicator.
Does low tire pressure location indicator continues displaying?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is DTC detected?
YES
>> Perform DTC diagnosis procedure. Refer to
NO
>> GO TO 4.
4.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for power supply and ground circuit. Refer to
BCS-125, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace error-detected parts.
WT-54
< SYMPTOM DIAGNOSIS >
[WITH TPMS]
TIRE PRESSURE SENSOR ID REGISTRATION CANNOT BE COMPLETED
TIRE PRESSURE SENSOR ID REGISTRATION CANNOT BE COMPLETED
Description
INFOID:0000000010339563
The ID of the tire pressure sensor installed in each wheel cannot be registered in the tire pressure monitoring
system. Inspect the tire pressure sensor or the tire pressure monitoring system circuit.
Diagnosis Procedure
INFOID:0000000010339564
1.
CHECK TIRE PRESSURE SENSOR INSTALLATION
Check visually that tire pressure sensors are installed to each wheels correctly.
NOTE:
In the following case, tire pressure monitoring system (TPMS) does not function.
• Tire pressure sensor(s) are not installed.
• Tire pressure sensor(s) of other cars are installed.
Are the genuine NISSAN tire pressure sensors are installed correctly?
YES
>> GO TO 2.
NO
>> Replace and/or Install tire pressure sensor(s). Refer to
WT-62, "Removal and Installation"
. GO TO
3.
2.
CHECK TIRE PRESSURE SENSOR ACTIVATION TOOL
Check tire pressure sensor activation tool.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the battery of tire pressure sensor activation tool or repair/replace the tire pressure sen-
sor activation tool.
3.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
CAUTION:
To perform ID registration, observe the following points:
• Never register ID in a place where radio waves are interfered (e.g. radio tower).
• Never register ID in a place close to vehicles including TPMS.
Is tire pressure sensor ID registration completed?
YES
>> INSPECTION END
NO
>> GO TO 4.
4.
CHECK TIRE PRESSURE SIGNAL
Change the work location and perform ID registration again.
NOTE:
Depending on the tire pressure sensor position*, a blind spot exists, and the tire pressure receiver gets a
poor reception. If an ID registration is performed under this condition, the registration may not be completed.
In such case, follow the instructions below to improve the radio wave receiving environment.
• Rotate tire by 90
°
, 180
°
, or 270
°
. (This step is to change tire pressure sensor position.)
• Open the door close to the tire of which ID registration is ongoing.
*: Radio wave reception condition depends on vehicle architecture (e.g. body harness layout, tire wheel
design) or environment.
When ID registration is performed, which wheels do not react?
All wheels react and ID registration is possible.>>INSPECTION END
Only certain wheel(s) do not react.>>Replace applicable tire pressure sensor. Refer to
All wheels do not react.>>Replace the BCM. Refer to
HAZARD WARNING LAMP REMAINS ON
WT-55
< SYMPTOM DIAGNOSIS >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
HAZARD WARNING LAMP REMAINS ON
Description
INFOID:0000000010339565
The hazard warning lamp remains on.
Diagnosis Procedure
INFOID:0000000010339566
1.
CHECK HAZARD WARNING LAMP OPERATION
Check hazard warning lamp operation with hazard switch.
Is the operation normal?
YES
>> GO TO 2.
NO
>> Perform trouble diagnosis for the hazard warning lamp. Refer to
EXL-143, "Diagnosis Procedure"
EXL-299, "Diagnosis Procedure"
(halogen headlamp).
2.
CHECK HAZARD REQUEST SIGNAL CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect the hazard warning switch connector and BCM harness connector.
3.
Check the continuity between the BCM harness connector and the ground.
Is the inspection result normal?
YES
>> Replace the BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
BCM
—
Continuity
Connector
Terminal
M13
36
Ground
Not existed
WT-56
< SYMPTOM DIAGNOSIS >
[WITH TPMS]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000010339567
Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
(Al
u
mi
nu
m
whe
e
l)
(S
te
el
whe
e
l)
(Al
u
mi
nu
m
whe
e
l)
(S
te
el
whe
e
l)
—
—
NVH in DLN
section.
NVH in DLN
section.
NVH in F
AX and FSU sections.
NVH in RAX
and RSU sections.
Ref
e
r to
TI
RE in
th
is ch
art
.
Ref
e
r to
ROAD WHE
E
L i
n
t
h
is cha
rt.
NVH in F
AX, RAX
section.
NVH in BR section.
NVH in ST section.
Possible cause and SUSPECTED PARTS
Im
p
rop
er i
n
s
ta
lla
ti
o
n
, lo
os
en
es
s
Out
-of-ro
un
d
Un
ba
la
nc
e
Incorrect t
ire
pressure
Uneven tire
wear
Def
o
rm
ati
o
n
o
r da
ma
ge
No
n-u
n
if
ormi
ty
In
co
rrec
t t
ire
si
ze
PROPELLER SHAFT
DIFF
ERENTIAL
FRONT A
X
LE
AND FRONT SUSP
ENSION
REAR A
X
LE
AND REAR SUSP
ENSION
TI
RE
ROAD WHEE
LS
DRIVE SHAFT
BRAKE
STE
E
RING
Symptom
TIRE
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
×
×
×
×
ROAD
WHEEL
Noise
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
Shimmy, Judder
×
×
×
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
×
ROAD WHEEL
WT-57
< PERIODIC MAINTENANCE >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PERIODIC MAINTENANCE
ROAD WHEEL
Inspection
INFOID:0000000010339568
APPEARANCE
Road Wheel
• Check road wheel for deformation, cracks, corrosion and other damage.
• Check wheel nuts for looseness by using torque wrench.
Tire
• Check entire circumference and both sides of each tire for deformation, cracks, scratch and other damage.
• Check tire tread for wear and foreign matter such as nails and small rock.
• Check that tire pressure is the specified value.
Wheel Balance Adjustment (Aluminum Wheel)
INFOID:0000000010339569
PREPARATION BEFORE ADJUSTMENT
Using releasing agent, remove double-faced adhesive tape from the road wheel.
CAUTION:
• Never scratch the road wheel during removal.
• After removing double-faced adhesive tape, wipe clean traces of releasing agent from the road
wheel.
ADJUSTMENT
• The details of the adjustment procedure are different for each model of wheel balancer. Therefore, refer to
each instruction manual.
• If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for aluminum wheels.
1.
Set road wheel on tire balance machine using the center hole as a guide. Start the tire balance machine.
2.
When inner and outer unbalance values are shown on the tire balance machine indicator, multiply outer
unbalance value by 5/3 to determine balance weight that should be used. Select the outer balance weight
with a value closest to the calculated value above and install to the designated outer position of, or at the
designated angle in relation to the road wheel.
CAUTION:
• Never install the inner balance weight before installing the outer balance weight.
• Before installing the balance weight, always to clean the mating surface of the road wheel.
a.
Indicated unbalance value
×
5/3 = balance weight to be installed
Calculation example:
23 g (0.81 oz)
×
5/3 = 38.33 g (1.35 oz)
⇒
40 g (1.41 oz) bal-
ance weight (closer to calculated balance weight value)
NOTE:
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4
⇒
35 g (1.23 oz)
37.5
⇒
40 g (1.41 oz)
b.
Installed balance weight in the position.
Wheel nut tightening torque
: Refer to
.
Tire pressure
: Refer to
SMA054D
WT-58
< PERIODIC MAINTENANCE >
[WITH TPMS]
ROAD WHEEL
• When installing balance weight (1) to road wheels, set it into
the grooved area (A) on the inner wall of the road wheel as
shown in the figure so that the balance weight center (B) is
aligned with the tire balance machine indication position
(angle) (C).
CAUTION:
• Always use genuine NISSAN balance weights.
• Balance weights are non-reusable; always replace with
new ones.
• Never install three or more sheets of balance weight.
c.
If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other as shown in
the figure.
CAUTION:
Never install one balance weight sheet on top of another.
3.
Start the tire balance machine again.
4.
Install drive-in balance weight on inner side of road wheel in the tire balance machine indication position
(angle).
CAUTION:
Never install three or more balance weight.
5.
Start the tire balance machine. Check that the inner and outer residual unbalance value is within the
allowable unbalance value.
CAUTION:
If either residual unbalance value exceeds limit, repeat installation procedures.
Wheel Balance Adjustment (Steel Wheel)
INFOID:0000000010339570
PREPARATION BEFORE ADJUSTMENT
Remove balance weight from the road wheel.
CAUTION:
Never scratch the road wheel during removal.
ADJUSTMENT
JPEIC0040ZZ
PEIA0033E
Allowable unbalance value
Dynamic (At flange)
: Refer to
.
Static (At flange)
: Refer to
.
ROAD WHEEL
WT-59
< PERIODIC MAINTENANCE >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
• The details of the adjustment procedure are different for each model of wheel balancer. Therefore, refer to
each instruction manual.
• If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for steel wheels.
1.
Set road wheel to wheel balancer, and then start wheel balancer.
2.
Install balance weight to road wheel according to the unbalance and position (angle) displayed on wheel
balancer.
CAUTION:
• Always use genuine NISSAN balance weights.
• Balance weights are non-reusable; always replace with new ones.
• Always use a plastic hammer when attaching the weight.
• Never install three or more balance weights on one side.
3.
Start the tire balance machine. Check that the inner and outer residual unbalance value is within the
allowable unbalance value.
CAUTION:
If either residual unbalance value exceeds limit, repeat installation procedures.
Tire Rotation
INFOID:0000000010339571
• Follow the maintenance schedule for tire rotation service intervals.
• When installing the wheel, tighten wheel nuts to the specified
.
CAUTION:
• Never include the T-type spare tire when rotating the tires.
• When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
• Never tighten wheel nut at torque exceeding the criteria.
• Use NISSAN genuine wheel nut.
• After tire rotation, perform following:
- Perform the ID registration. Refer to
.
- Perform TPMS temperature calibration. Refer to
WT-14, "TPMS temperature calibration"
.
Allowable unbalance value
Dynamic (At flange)
: Refer to
.
Static (At flange)
: Refer to
.
SMA829C
WT-60
< REMOVAL AND INSTALLATION >
[WITH TPMS]
ROAD WHEEL TIRE ASSEMBLY
REMOVAL AND INSTALLATION
ROAD WHEEL TIRE ASSEMBLY
Exploded View
INFOID:0000000010339579
Removal and Installation
INFOID:0000000010339580
REMOVAL
1.
Remove wheel nuts.
2.
Remove tire assembly.
INSTALLATION
Note the following, install in the reverse order of removal.
• When replacing or rotating wheels, perform following;
- Perform the ID registration. Refer to
.
- Perform TPMS temperature calibration. Refer to
WT-14, "TPMS temperature calibration"
.
Inspection
INFOID:0000000010339581
1.
Check tires for wear and improper inflation.
2.
Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.
a.
Remove tire from aluminum wheel and mount on a tire balance machine.
b.
Set dial indicator as shown in the figure.
c.
Check runout, if the axial runout (A) or radial runout (B) exceeds
the limit, replace aluminum wheel.
1.
Tire assembly
: N·m (kg-m, ft-lb)
E1EIA0119GB
Limit
Axial runout (A)
: Refer to
.
Radial runout (B)
: Refer to
.
SEIA0737E
ROAD WHEEL TIRE ASSEMBLY
WT-61
< REMOVAL AND INSTALLATION >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
How to Handle Puncture Repair Agent (With Puncture Repair Kit)
INFOID:0000000010493950
CAUTION:
• Never spill the sealant in the tire during repair.
• If the sealant spills, wipe it out with a waste cloth.
• Never reuse the repair kit hose used for a temporary repair of a flat tire because some of the punc-
ture repair agent remains in the hose.
• After using a puncture repair agent, replace valve core with a new one.
• Complete tire blowout repair or tire replacement within two days from the tire removal work start to
prevent the hardening of the repair agent which attached to tire pressure sensor. Replace tire pres-
sure sensor with a new one if tire blowout repair or tire replacement does not be completed within
two days from tire removal work start.
1.
Remove tires from the vehicle.
2.
Remove tire from road wheel, using a tire changer.
CAUTION:
• When deflating a tire, cover the valve with a waste cloth to prevent the sealant from splattering.
• Never spill the sealant in the tire during repair.
3.
Dispose of sealant in the removed tire.
CAUTION:
• Wipe out sealant spilled on the road wheel, tire, tire changer, and floor with a waste cloth.
• Drained sealant or expired sealant returned by the customer must be disposed according to the
law and local regulations.
• Fix a tire blowout, if repairable.
NOTE:
Sealant blocks holes caused by blowouts. These holes may not be found and repaired, depending on
the level of blowout. Therefore, it is necessary to check tire air pressure frequently and replace tire with
a new one, if the air pressure is decreasing.
• Replace tire with a new one, if not repairable.
CAUTION:
Never dispose of tires with the sealant contained.
WT-62
< REMOVAL AND INSTALLATION >
[WITH TPMS]
TIRE PRESSURE SENSOR
TIRE PRESSURE SENSOR
Exploded View
INFOID:0000000010339582
Removal and Installation
INFOID:0000000010339583
REMOVAL
1.
Remove tire assembly. Refer to
WT-60, "Removal and Installation"
2.
Remove valve cap, valve core and then deflate tire.
NOTE:
If the tire is reused, apply a matching mark to the position of the tire road wheel valve hole for the purpose
of wheel balance adjustment after installation.
3.
Remove valve nut retaining tire pressure sensor and allow tire pressure sensor to fall into tire.
4.
Use the tire changer and disengage the tire beads.
CAUTION:
• Verify that the tire pressure sensor (1) is at the bottom of
the tire while performing the above.
• Never damage the road wheel or tire pressure sensor.
5.
Apply bead cream or an equivalent to the tire beads.
6.
Set tire onto the tire changer turntable so that the tire pressure
sensor inside the tire is located close to the road wheel valve
hole.
1.
Tire pressure sensor
2.
Washer/Grommet seal
3.
Valve nut
4.
Valve core
5.
Valve cap
6.
Valve stem assembly
Refer to
for symbols not described on the above.
JMEIA0243GB
JPEIC0104ZZ
TIRE PRESSURE SENSOR
WT-63
< REMOVAL AND INSTALLATION >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
7.
Turn tire so that valve hole is at bottom and bounce so that tire
pressure sensor (1) is near valve hole. Carefully lift tire onto
turntable and position valve hole (and tire pressure sensor) 270
degree from tire changer arm (2).
CAUTION:
Never damage the road wheel and tire pressure sensor.
8.
Remove tire pressure sensor from tire.
9.
Remove the grommet seal and washer.
10. Remove valve stem in the direction shown by arrow (
).
INSTALLATION
CAUTION:
Replace valve stem assembly if the valve stem has deformations, cracks, damage or corrosion.
1.
Apply bead cream or an equivalent to the tire beads.
2.
Install the tire inside beads (1) onto the road wheel (2) in the
position shown in the figure.
3.
Set valve stem in the tire pressure sensor.
4.
Install the washer (1) in the valve stem, and then install grommet
seal (2) in the valve stem.
CAUTION:
• Never reuse grommet seal.
• Check the direction of the grommet seal.
• Insert grommet seal all the way to the base.
JPEIC0014GB
JSEIA0378ZZ
JPEIC0105ZZ
: Upper side
JMEIA0211ZZ
WT-64
< REMOVAL AND INSTALLATION >
[WITH TPMS]
TIRE PRESSURE SENSOR
• Direct the cut part (A) of washer to the center of valve
stem as shown in the figure.
5.
Follow the procedure below and install the tire pressure sensor to the road wheel.
a.
Check the condition of valve stem before installing tire pressure
sensor to road wheel.
CAUTION:
The base of valve stem (A) must be positioned in the
groove of the metal plate as shown in the figure.
b.
Hold tire pressure sensor as shown in the figure, and press the sensor in the direction shown by arrow
(
) to bring it into absolute contact with road wheel. After this, tighten valve nut to the specified torque.
CAUTION:
• Never reuse valve core and valve cap.
• Check that grommet seal is free of foreign matter.
• Check that grommet seal contacts horizontally with road wheel.
• Check again that the base of valve stem is positioned in the groove of the metal plate.
• Manually tighten valve nut all the way to the wheel. (Never use a power tool to avoid impact.)
• Never tighten valve nut to more than the specified torque. It cause grommet seal damage.
• Never tighten valve nut to less than the specified torque. It cause air leak.
JMEIA0212ZZ
JSEIA0376GB
Valve nut tightening torque
: 7.7 N·m (0.79 kg-m, 68 in-lb)
JSEIA0465GB
TIRE PRESSURE SENSOR
WT-65
< REMOVAL AND INSTALLATION >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
6.
Set the tire onto the turntable so that the tire changer arm (2) is
at a position approximately 270
°
from the tire pressure sensor
(1).
CAUTION:
Be sure that the arm does not contact the tire pressure sen-
sor.
7.
Install the tire outer side beads onto the road wheel.
CAUTION:
When installing, check that the tire does not turn together
with the road wheel.
8.
Check the tire pressure for all wheels and adjust to the specified
value. Refer to
NOTE:
Before adding air, align the tire with the position of the matching mark applied at the time of removal.
9.
Install tire to the vehicle. Refer to
WT-60, "Removal and Installation"
10. Perform tire pressure sensor ID registration. Refer to
.
11. Perform TPMS temperature calibration. Refer to
WT-14, "TPMS temperature calibration"
.
Disposal
INFOID:0000000010339584
CAUTION:
• When discarding tire pressure sensor, remove battery from tire pressure sensor.
• Dispose of battery to the law and local regulations.
1.
Remove battery from tire pressure sensor.
NOTE:
The battery is sealed by tire pressure sensor with urethane.
a.
Remove urethane from tire pressure sensor.
b.
Cut battery terminal (A), then remove battery (1) from tire pres-
sure sensor.
JPEIC0014GB
JSEIA0729ZZ
WT-66
< SERVICE DATA AND SPECIFICATIONS (SDS)
[WITH TPMS]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Road Wheel
INFOID:0000000010297287
Tire Air Pressure
INFOID:0000000010297288
Unit: kPa (kgf/cm
2
, psi)
*1
: The passengers are 3 or less.
*2
: The passengers are more than 3.
Kind of wheel
Aluminum
Steel
Conventional
For temporary use
Maximum radial runout limit
Lateral deflection
Less than 0.3 mm
(0.012 in)
Less than 0.8 mm
(0.031 in)
Less than 1.2 mm
(0.047 in)
Vertical deflection
Less than 0.7 mm
(0.028 in)
Less than 1.3 mm
(0.051 in)
Maximum allowable unbalance limit
Dynamic (At flange)
Less than 10 g (0.35 oz) (one side)
Static (At flange)
Less than 20 g (0.71 oz)
Wheel nuts tightening torque
112.6 N·m (11 kg–m, 83 ft–lb)
Tire size
Air pressure
Front
Rear
Normal condition
Full condition
Normal condition
Full condition
215/65R16 98H
260 (2.6, 38)
240 (2.4, 35)
*1
260 (2.6, 38)
*2
215/60R17 96H
230 (2.3, 33)
210 (2.1, 30)
*1
260 (2.6, 38)
*2
215/55R18 83T/85T/87T/88T
225/45R19 92W/95W
PRECAUTIONS
WT-67
< PRECAUTION >
[WITHOUT TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PRECAUTION
PRECAUTIONS
Precautions for Removing Battery Terminal
INFOID:0000000010503767
• With the adoption of Auto ACC function, ACC power is automatically supplied by operating the intelligent key
or remote keyless entry or by opening/closing the driver side door. In addition, ACC power is supplied even
after the ignition switch is turned to the OFF position, i.e. ACC power is supplied for a certain fixed time.
• When disconnecting the 12V battery terminal, turn off the ACC
power before disconnecting the 12V battery terminal, observing
“How to disconnect 12V battery terminal” described below.
NOTE:
Some ECUs operate for a certain fixed time even after ignition
switch is turned OFF and ignition power supply is stopped. If the
battery terminal is disconnected before ECU stops, accidental DTC
detection or ECU data damage may occur.
HOW TO DISCONNECT 12V BATTERY TERMINAL
Disconnect 12V battery terminal according to Instruction 1 or Instruction 2 described below.
For vehicles parked by ignition switch OFF, refer to Instruction 2.
INSTRUCTION 1
1.
Open the hood.
2.
Turn key switch to the OFF position with the driver side door opened.
3.
Get out of the vehicle and close the driver side door.
4.
Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse
of the specified time.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
5.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
INSTRUCTION 2 (FOR VEHICLES PARKED BY IGNITION SWITCH OFF)
1.
Unlock the door with intelligent key or remote keyless entry.
NOTE:
At this moment, ACC power is supplied.
2.
Open the driver side door.
3.
Open the hood.
4.
Close the driver side door.
5.
Wait at least 3 minutes.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
6.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
SEF289H
D4D engine
: 20 minutes
K9K engine
: 4 minutes
M9R engine
: 4 minutes
R9M engine
: 4 minutes
V9X engine
: 4 minutes
WT-68
< PRECAUTION >
[WITHOUT TPMS]
PRECAUTIONS
• For vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON
the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of main battery and sub battery discon-
nected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
Service Notice and Precautions for Road Wheel
INFOID:0000000010382304
• Genuine NISSAN aluminum wheel is designed for each type of vehicle. Use it on the specified vehicle only.
• Use Genuine NISSAN parts for the road wheels, valve caps and wheel nuts.
• Always use them after adjusting the wheel balance. For the balance weights, use Genuine NISSAN alumi-
num wheel weights.
• Use caution when handling the aluminum wheels, because they can be easily scratched. When removing
dirt, do not use any abrasives, a wire brush, or other items that may scratch the coating. Use a neutral deter-
gent if a detergent is needed.
• After driving on roads scattered with anti-icing salts, wash off the wheels completely.
• When installing road wheels onto the vehicle, always wipe off any dirt or foreign substances to prevent them
from being trapped between the contact surfaces of wheel.
• Never apply oil to nut and bolt threads.
• When tightening the valve cap there is a risk of damaging the valve cap if a tool is used. Tighten by hand.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст