Nissan Note E12. Manual — part 699
WIPER AND WASHER SYSTEM SYMPTOMS
WW-47
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Front wiper operates ab-
normally because...
Intermittent adjust-
ments cannot be made.
• Combination switch (wiper and washer
switch)
• Harness between combination switch (wip-
er and washer switch) and BCM
• BCM
Combination switch (wiper
and washer switch)
Refer to
Wiper/washer will not
operate together.
• Combination switch (wiper and washer
switch)
• Harness between combination switch (wip-
er and washer switch) and BCM
• BCM
Combination switch (wiper
and washer switch)
Refer to
Wipers will not return to
stop position (repeat-
edly operates for 10
seconds and then
stops for 20 seconds.
Wipers then stop oper-
ating).
• IPDM E/R
• Harness between IPDM E/R and front wiper
motor
• Front wiper motor
Front wiper auto stop signal
circuit
Refer to
.
Rear wiper does not op-
erate.
ON only
• Combination switch (wiper and washer
switch)
• Harness between combination switch (wip-
er and washer switch) and BCM
• BCM
Combination switch (wiper
and washer switch)
Refer to
INT only
• Combination switch (wiper and washer
switch)
• Harness between combination switch (wip-
er and washer switch) and BCM
• BCM
Combination switch (wiper
and washer switch)
Refer to
ON and INT
• Combination switch (wiper and washer
switch)
• Harness between combination switch (wip-
er and washer switch) and BCM
• BCM
Combination switch (wiper
and washer switch)
Refer to
• BCM
• Harness between rear wiper motor and
BCM
• Harness between rear wiper motor and
ground
• Rear wiper motor
Rear wiper motor circuit
Refer to
Rear wiper does not
stop.
ON only
• Combination switch (wiper and washer
switch)
• BCM
Rear wiper motor circuit
Refer to
INT only
• Combination switch (wiper and washer
switch)
• BCM
Combination switch (wiper
and washer switch)
Refer to
Rear wiper does not op-
erate normally.
Wiper is not linked to
the washer operation.
• Combination switch (wiper and washer
switch)
• Harness between rear wiper motor and
BCM
• BCM
Combination switch (wiper
and washer switch)
Refer to
BCM
—
Rear wiper does not re-
turn to the Stop position
(Stops after a five-sec-
ond operation).
• BCM
• Harness between rear wiper motor and
BCM
• Rear wiper motor
Rear wiper auto stop signal
circuit
Refer to
Rear wiper stops after
operating for five sec-
onds when ignition
switch is turned ON.
Symptom
Possible malfunction
Reference
WW-48
< SYMPTOM DIAGNOSIS >
WIPER AND WASHER SYSTEM SYMPTOMS
Front and rear washer
motor does not operate.
Front and rear washer
motor does not operate
when the washing
windshield.
• Combination switch (wiper and washer
switch)
• Harness between combination switch (wip-
er and washer switch) and BCM
• BCM
Combination switch (wiper
and washer switch)
Refer to
• Harness between rear combination switch
(wiper and washer switch) and front and
rear washer motor.
• Front and rear washer motor
Front and rear washer motor
circuit
Refer to
Symptom
Possible malfunction
Reference
FRONT WIPER DOES NOT OPERATE
WW-49
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER DOES NOT OPERATE
Description
INFOID:0000000009541159
The front wiper does not operate under any operation conditions.
Diagnosis Procedure
INFOID:0000000009541160
Regarding Wiring Diagram information, refer to
.
1.
CHECK WIPER RELAY OPERATION
IPDM E/R AUTO ACTIVE TEST
1. Start IPDM E/R auto active test. Refer to
PCS-10, "CONSULT Function (IPDM E/R)"
.
2. Check that the front wiper operates on LO and HI operation.
CONSULT ACTIVE TEST
1. Select FR WIPER of BCM (WIPER) active test item.
2. Check front wiper operation.
Is the inspection result normal?
YES
>> GO TO 5
NO
>> GO TO 2
2.
CHECK FRONT WIPER MOTOR FUSE
.
Is the fuse blown?
YES
>> Replace the fuse after repairing the affected circuit.
NO
>> GO TO 3
3.
CHECK FRONT WIPER MOTOR GROUND CIRCUIT
.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK FRONT WIPER MOTOR OUTPUT VOLTAGE
1. Turn the ignition switch ON.
2. With CONSULT, select FRONT WIPER of IPDM E/R ACTIVE TEST item.
3. Check voltage between IPDM E/R harness connector and ground while wipers are operating.
Is the inspection result normal?
YES
>> Replace front wiper motor. Refer to
WW-61, "Removal and Installation"
LO
: Front wiper LO operation
HI
: Front wiper HI operation
OFF
: Front wiper stop
Terminals
FRONT WIPER
Voltage (Approx.)
(+)
(
−)
IPDM E/R
Ground
Connector
Terminal
E45
17
LO
Battery voltage
OFF
0 V
18
HI
Battery voltage
OFF
0 V
WW-50
< SYMPTOM DIAGNOSIS >
FRONT WIPER DOES NOT OPERATE
NO
>> Replace IPDM E/R. Refer to
PCS-30, "Removal and Installation"
5.
CHECK FRONT WIPER REQUEST SIGNAL INPUT
1. With CONSULT, select FR WIP REQ in DATA MONITOR of IPDM E/R.
2. Switch the front wiper switch to HI and LO.
3. Check the status of FR WIP REQ while operating the switch.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-30, "Removal and Installation"
NO
>> GO TO 6
6.
CHECK COMBINATION SWITCH (WIPER AND WASHER SWITCH)
Check combination switch (wiper and washer switch). Refer to
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-67, "Removal and Installation"
NO
>> Repair or replace the applicable parts.
Data monitor
Condition
Status
FR WIP REQ
Front wiper switch OFF
STOP
Front wiper switch LO
LOW
Front wiper switch HI
HI
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст