Nissan Note E12. Manual — part 700
NORMAL OPERATING CONDITION
WW-51
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
NORMAL OPERATING CONDITION
Description
INFOID:0000000009541161
FRONT WIPER PROTECTION FUNCTION
IPDM E/R detects front wiper stop position by a front wiper stop position signal.
When a front wiper stop position signal is in the conditions listed below, IPDM E/R stops power supply to wiper
after repeating a front wiper 10 seconds activation and 20 seconds stop.
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
REAR WIPER MOTOR PROTECTION FUNCTION
• BCM may stop rear wiper to protect the rear wiper motor when the rear wiper is stopped for 5 seconds or
more due to a snowfall.
• Rear wiper operates normally one minute after the obstacles are removed with rear wiper OFF.
Ignition switch
Front wiper switch
Front wiper stop position signal
ON
OFF
The front wiper stop position signal (stop position) cannot be input for 10 seconds.
ON
The front wiper stop position signal does not change for 10 seconds.
WW-52
< REMOVAL AND INSTALLATION >
WASHER TANK
REMOVAL AND INSTALLATION
WASHER TANK
Exploded View
INFOID:0000000009578899
Removal and Installation
INFOID:0000000009578900
REMOVAL
1. Remove front under cover. Refer to
EXT-25, "FRONT UNDER COVER : Removal and Installation"
.
2. Remove fender protector (RH). Refer to
EXT-24, "Removal and Installation"
.
3. Remove washer tank clip (A) using a suitable tool.
1.
Washer tank cap
2.
Washer tank
3.
Front washer motor
A. Front washer motor seal
Front
ALLIA1318ZZ
ALKIA3175ZZ
WASHER TANK
WW-53
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
4. Release the front washer tube (2) and rear washer tube (1) from
washer tank (3).
5. Release the harness (4) from the washer tank (3).
6. Disconnect the harness connector from the washer pump.
7. Remove bolts (A) and washer tank (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, add water to the top of the washer tank inlet to check that no leaks exist.
• Fill washer tank with specified amount of fluid. Refer to
.
ALLIA1305ZZ
ALLIA1303ZZ
WW-54
< REMOVAL AND INSTALLATION >
FRONT WASHER MOTOR
FRONT WASHER MOTOR
Exploded View
INFOID:0000000009606283
Removal and Installation
INFOID:0000000009606284
REMOVAL
1. Remove front under cover. Refer to
EXT-25, "FRONT UNDER COVER : Removal and Installation"
.
2. Remove fender protector (RH). Refer to
EXT-24, "Removal and Installation"
.
3. Disconnect the harness connector from the front washer motor.
4. Remove front washer tube and rear washer tube from front washer motor.
5. Remove front washer motor from washer tank.
6. Remove front washer motor seal from washer tank.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not rotate or damage the front washer motor seal when installing the front washer motor.
1.
Washer tank cap
2.
Washer tank
3.
Front washer motor
A.
Front washer motor seal
Front
ALLIA1318ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст