Nissan Note E12. Manual — part 591
PREPARATION
ST-3
< PREPARATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009385581
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000009385582
Tool number
(Kent-Moore No.)
Tool name
Description
ST3127S000
(J-25765-A)
Preload gauge
Inspecting steering column rotating torque,
pinion rotating torque and ball joint rotating
torque
—
(J-44372)
Pull gauge
Measuring steering wheel turning force or rack
sliding force
ZZA0806D
LST024
Tool name
Description
Ball joint remover
Remove steering outer socket
Boot band crimping tool
Installing boot clamp (large diameter)
S-NT146
ZZA1229D
ST-4
< PREPARATION >
PREPARATION
Steering wheel puller
Removing steering wheel
Power tool
Loosening nuts, screws and bolts
Tool name
Description
ZZA0819D
PIIB1407E
STEERING WHEEL
ST-5
< BASIC INSPECTION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
BASIC INSPECTION
STEERING WHEEL
Inspection
INFOID:0000000009385583
CONDITION OF INSTALLATION
• Check installation conditions of steering gear, front suspension, axle and steering column.
• Check if movement exists when steering wheel is moved up and down, to the left and right and to the axial
direction.
• Verify that the steering gear nuts are tightened to specification. Refer to
.
STEERING WHEEL PLAY
1. Set the front wheels and tires in the straight-ahead position, start engine, then lightly turn steering wheel
to the left and right until the front wheels start to move. Measure steering wheel movement on the outer
circumference.
2. When the measurement value is outside the standard value, check backlash for each joint of steering col-
umn and installation condition of steering gear.
STEERING WHEEL NEUTRAL POSITION
Check steering wheel neutral position using the following procedure:
1. Confirm that front wheel alignment is correct. Refer to
2. Set the front wheels and tires in the straight-ahead position, check if steering wheel is in the neutral posi-
tion.
3. If it is not in the neutral position, remove steering wheel and reinstall it correctly.
4. If the neutral position cannot be attained by repositioning the steering wheel two teeth or less on steering
stem, loosen the steering gear outer socket lock nuts, then adjust the inner sockets by the same amount
in the opposite direction.
5. Re-check the front wheel alignment. Refer to
STEERING WHEEL TURNING FORCE
1. Park vehicle on a level and dry surface, set parking brake.
2. Tires need to be inflated normal pressure. Refer to
.
3. Start engine.
4. Check steering wheel turning force using Tool when steering
wheel has been turned 360
° from the neutral position.
5. If steering wheel turning force is out of specification, inspect
ST-19, "Steering Wheel Turning
6. If steering column meets specification, inspect steering gear.
.
FRONT WHEEL TURNING ANGLE
1. Perform toe-in inspection. Refer to
.
Steering wheel axial end play
: Refer to
Steering wheel play on the
outer circumference
: Refer to
ST-19, "Steering Wheel Axial End Play and Play"
.
Tool number :
—
(J-44372)
Steering wheel turning
force
: Refer to
SGIA1523J
ST-6
< BASIC INSPECTION >
STEERING WHEEL
CAUTION:
Perform front wheel turning angle inspection, after toe-in inspection.
2. Place front wheels on turning radius gauges and rear wheels on
stands, so that vehicle can be level.
3. Check the maximum inner and outer wheel turning angles for
(LH/ RH) wheels and tires.
• With the engine at idle, turn steering wheel from full left stop to
full right stop and measure the turning angles.
• Check the following items when turning angle is out of the standard.
- Check rack stroke (L).
- Disassemble steering gear to check the cause that rack stroke
is outside of the standard.
• Steering angles are not adjustable. Check steering gear, steer-
ing column and front suspension components for wear or dam-
age if any of the turning angles are different from the specified
value. Replace any of them, if any non-standard condition
exists.
FAA0016D
Inner wheel (Angle: A)
: Refer to
.
Outer wheel (Angle: B)
: Refer to
.
SGIA0055E
Rack stroke (L)
: Refer to
JSGIA0272ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст