Nissan Note E12. Manual — part 592
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
ST-7
< SYMPTOM DIAGNOSIS >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009385584
Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
"
"
Possible cause and SUSPECTED PARTS
Ou
ter/
inn
er
so
ck
et
ba
ll
joi
nt
swi
ng
ing
to
rqu
e
O
u
ter/
inn
er
so
ck
et
ba
ll
joi
nt
rot
ati
ng
to
rque
O
u
ter/
inn
er
so
ck
et
ba
ll
joi
nt
en
d p
la
y
S
te
e
ring
whe
e
l pl
ay
Im
pro
p
er
st
ee
ring
wh
ee
l
Im
p
rop
er i
ns
tal
la
tio
n o
r lo
os
en
es
s of
til
t l
oc
k l
ev
er
M
ou
nt
ing
loos
e
nes
s
S
tee
rin
g c
o
lum
n
de
form
at
ion
o
r da
ma
ge
Im
p
rop
er i
ns
tal
la
tio
n o
r lo
os
en
es
s of
st
ee
ring
c
olu
m
n
S
te
eri
ng
li
nk
ag
e l
oo
se
ne
ss
A
XLE and
SUSP
ENSION
TI
RE
ROAD W
H
EEL
DRIV
E SHAFT
BR
AK
E
Symptom
Noise
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
Shudder
×
×
×
×
×
×
×
ST-8
< REMOVAL AND INSTALLATION >
STEERING WHEEL
REMOVAL AND INSTALLATION
STEERING WHEEL
Exploded View
INFOID:0000000009385585
Removal and Installation
INFOID:0000000009385586
REMOVAL
1. Set the front wheels and tires in the straight-ahead position.
2. Remove driver air bag module. Refer to
SR-12, "Removal and Installation"
.
3. Remove steering wheel lock nut.
4. Remove steering wheel using suitable tool.
CAUTION:
Place a piece of tape across the spiral cable so it will not be rotated out of position.
5. Inspect steering wheel near the puller holes for damage. Replace as necessary.
INSTALLATION
Installation is in the reverse order of removal.
Align spiral cable correctly before installing steering wheel. Make sure that the spiral cable is in the neutral
position. Refer to
.
CAUTION:
• The spiral cable may snap due to steering operation if the cable is not installed in the correct posi-
tion.
• With the steering linkage disconnected, the cable may snap by turning the steering wheel beyond
the limited number of turns.
1.
Steering wheel
JSGIA0704GB
STEERING COLUMN
ST-9
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
STEERING COLUMN
Exploded View
INFOID:0000000009385587
Removal and Installation
INFOID:0000000009385588
CAUTION:
• Any time the ignition switch has been disconnected, removed or installed; the vehicle keys must be
re-registered in the BCM. Refer to CONSULT operations manual.
• Care must be taken not to rotate the steering gear during the removal or installation of the steering
column.
• Care must be taken not to allow axial impact to the steering column during removal or installation.
REMOVAL
1. Set the front wheels and tires in the straight-ahead position.
2. Set the steering column tilt to the lowest position.
CAUTION:
Securely lock the tilt lever.
3. Remove instrument lower panel LH. Refer to
IP-24, "Removal and Installation"
4. Remove spiral cable. Refer to
SR-15, "Removal and Installation"
.
5. Remove combination switch. Refer to
BCS-68, "Removal and Installation"
6. Remove the cluster lid A. Refer to
IP-21, "Removal and Installation"
.
7. Disconnect the switch harness connectors.
8. Set the steering column tilt to the middle position.
CAUTION:
Do not change the position of the tilt mechanism until the steering column is reinstalled.
9. Loosen the steering shaft lower joint bolt.
10. Remove the steering intermediate shaft upper bolt and separate the steering intermediate shaft from the
steering column. Refer to
ST-12, "Removal and Installation"
.
CAUTION:
• Place a matching mark on both steering intermediate shaft and steering column before removing
the steering intermediate shaft.
• When removing steering intermediate shaft, do not insert any tool into the yoke groove to pull
out the steering intermediate shaft or damage could occur. Replace steering intermediate shaft if
damaged.
11. Disconnect EPS control unit harness connectors.
1.
Steering column
2.
Clamp
AWGIA0294ZZ
ST-10
< REMOVAL AND INSTALLATION >
STEERING COLUMN
12. Remove steering column.
13. Remove EPS control unit from steering column if necessary. Refer to
STC-37, "Removal and Installation"
.
14. Remove clamp from steering column if necessary.
15. Inspect steering column after removal. Refer to
.
INSTALLATION
CAUTION:
• During installation, finger-tighten all of the bracket and joint retaining bolts, then tighten them to
specification.
• When installing the steering column cover, check that the vehicle harness is not stuck in the cover.
• Replace the steering column if it has been dropped or sustained an impact.
Installation is in the reverse order of removal.
• For intermediate shaft bolt direction, refer to
.
• When connecting intermediate shaft upper side (1) and column
shaft, make sure the bolt is securely seated in groove (A) of col-
umn shaft before final tightening.
• After installing steering column, perform self-diagnosis with CON-
SULT to ensure correct operation. Refer to
• Inspect steering column after installation. Refer to
Inspection
INFOID:0000000009385589
INSPECTION AFTER REMOVAL
• Check each part of steering column assembly for damage or other malfunctions. Replace if there are any
abnormal conditions.
• Measure steering column rotating torque using Tool (A). Replace
steering column if the rotating torque is outside specification
• Measure the steering column length (L) as shown, if vehicle has
been involved in a minor collision. Replace steering column if out-
side specification.
INSPECTION AFTER INSTALLATION
• Rotate steering wheel to make sure it is centered and there is no binding, noise or excessive steering effort.
• Make sure that the number of turns are the same from the straight-ahead position to the left and right locks.
• Check each part of steering column for damage or other malfunctions. Replace if there are any abnormal
conditions. Refer to
ST-19, "Steering Column Operating Range"
SGIA1295E
Tool number
:
—
(J-25765-A)
Rotating torque
.
JPGIA0085ZZ
Steering column length (L) : Refer to
.
JPGIA0111ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст