Nissan Note E12. Manual — part 311
EXL-112
< REMOVAL AND INSTALLATION >
COMBINATION SWITCH
COMBINATION SWITCH
Removal and Installation
INFOID:0000000009606282
CAUTION:
• Before servicing, turn the ignition switch OFF, disconnect both battery terminals and wait at least
three minutes.
• Do not use air or electric tools when removing or installing the combination switch.
REMOVAL
1. Disconnect the negative and positive battery terminals, then wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
2. Remove the steering column covers. Refer to
IP-17, "Removal and Installation"
.
3. Rotate steering wheel clockwise to access first combination
switch screw (A) and remove.
4. Rotate steering wheel counter-clockwise to access second com-
bination switch screw (A) and remove.
5. Disconnect the harness connector (B) from the combination
switch (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case a malfunction is detected by the air bag warning lamp, reset with the self-diagnosis function
and delete the memory with CONSULT.
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunc-
tions. Refer to
ALMIA0648ZZ
ALMIA0649ZZ
HAZARD SWITCH
EXL-113
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HAZARD SWITCH
Exploded View
INFOID:0000000009015739
Removal and Installation
INFOID:0000000009445907
REMOVAL
1. Remove cluster lid C. Refer to
IP-22, "Removal and Installation"
2. Release pawls and remove hazard switch.
INSTALLATION
Installation is in the reverse order of removal.
1. Cluster lid C
2. Hazard switch
Pawl
AWLIA2163ZZ
EXL-114
< REMOVAL AND INSTALLATION >
HEADLAMP AIMING SWITCH
HEADLAMP AIMING SWITCH
Exploded View
INFOID:0000000009015743
Removal and Installation
INFOID:0000000009641646
REMOVAL
1. Remove instrument lower panel LH. Refer to
IP-24, "Removal and Installation"
.
2. While pressing pawls, push the headlamp aiming switch to remove.
INSTALLATION
Installation is in the reverse order of removal.
1.
Instrument lower panel LH
2.
Headlamp aiming switch
Pawl
AWLIA2172ZZ
REAR COMBINATION LAMP
EXL-115
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REAR COMBINATION LAMP
Exploded View
INFOID:0000000009015744
Removal and Installation
INFOID:0000000009015745
REMOVAL
1. Remove rear combination lamp bolts.
2. Release the locating pin (A) of the rear combination lamp using
a suitable tool (B) as shown.
3. Disconnect the harness connector from the rear combination lamp and remove.
INSTALLATION
Installation is in the reverse order of removal.
Bulb Replacement
INFOID:0000000009015746
WARNING:
Do not touch bulb with bare hand while it is lit or right after being turned off. Burning may result.
CAUTION:
• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP BULB
Removal
1. Remove rear combination lamp. Refer to
EXL-115, "Removal and Installation"
1.
Rear combination lamp
A.
Grommet
B.
Clip
Locating pin
AWLIA2167ZZ
AWLIA2169ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст