Nissan Note E12. Manual — part 594
STEERING GEAR AND LINKAGE
ST-15
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
INSPECTION AFTER INSTALLATION
• Rotate steering wheel to make sure it is centered and there is no binding, noise or excessive steering effort.
• Make sure that the number of turns are the same from the straight-ahead position to the left and right locks.
• Check each part of steering system for damage or other malfunctions. Replace if there are any abnormal
conditions.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
• Check wheel alignment. Refer to
ST-16
< UNIT DISASSEMBLY AND ASSEMBLY >
STEERING GEAR AND LINKAGE
UNIT DISASSEMBLY AND ASSEMBLY
STEERING GEAR AND LINKAGE
Exploded View
INFOID:0000000009385596
Disassembly and Assembly
INFOID:0000000009385597
DISASSEMBLY
1. Remove outer socket lock nut and outer socket.
CAUTION:
When loosening outer socket lock nut, be sure to hold outer socket with a suitable tool to prevent
ball joint from contacting knuckle.
2. Remove inner boot clamp, outer boot clamp and remove boot.
CAUTION:
Do not damage inner socket or steering gear housing when removing boot.
3. Remove inner socket.
ASSEMBLY
1. Apply (Autolex A or Dow Corning 111) or equivalent to inner socket and turn pinion fully to retract inner
socket into gear housing assembly.
CAUTION:
Make sure there are no contaminants in the grease, on the inner socket, or inside the steering gear
housing.
1.
Joint cover
2.
Steering gear
3.
Inner socket
4.
Inner boot clamp
5.
Boot
6.
Outer boot clamp
7.
Outer socket
ALGIA0098GB
STEERING GEAR AND LINKAGE
ST-17
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
2. Install large end (1) of boot (2) to gear housing assembly.
3. Install small end (3) of boot (2) to inner socket boot mounting
groove.
4. Install outer boot clamp to boot small end using suitable tool.
5. Install inner boot clamp to boot large end using suitable tool.
CAUTION:
Do not reuse boot clamps.
6. Install outer socket.
7. Adjust inner socket to standard length (L) and then tighten lock
nut to the specified torque. Check length of inner socket (L)
again after tightening lock nut.
CAUTION:
The length achieved after toe-in adjustment is not neces-
sarily the above value.
8. Check wheel alignment. Refer to
CAUTION:
AWGIA0107ZZ
AST139
Inner socket length (L)
: Refer to
SGIA0167E
ST-18
< UNIT DISASSEMBLY AND ASSEMBLY >
STEERING GEAR AND LINKAGE
When tightening outer socket lock nut (1), be sure to hold
outer socket (2) using a suitable tool to prevent ball joint
from contacting knuckle.
Inspection
INFOID:0000000009385598
INSPECTION AFTER DISASSEMBLY
Boot
• Check boot for cracks and replace it if damage exists.
Steering gear
• Check steering gear for damage and scratches to the inner wall. Replace if there are any abnormal condi-
tions.
Outer Socket and Inner Socket
Check the following items and replace the component if outside specification:
BALL JOINT SWINGING FORCE
• Hook a Tool at the point shown and pull the spring balance. Make
sure that the Tool reads the specified value when ball stud and
inner socket start to move. Replace outer socket (1) and inner
socket (2) if they are outside the standard.
BALL JOINT AXIAL END PLAY
• Apply an axial load of 490 N (50 kg-f, 110 lb-f) to ball stud. Using a
dial gauge, measure amount of stud movement and make sure
that the value is within the following specified range. Replace outer
socket (1) and inner socket (2) if the measured value is outside the
standard.
JSGIA0538ZZ
Tool number :
—
(J-44372)
Measuring point of outer
socket (1)
: Ball stud upper side (A)
Measuring point of inner
socket (2)
: Point (B)
Swinging force : Refer to
Axial end play : Refer to
JPGIA0188ZZ
JSGIA0109ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст