Nissan Pathfinder. Manual — part 993
REAR STABILIZER
RSU-15
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR STABILIZER
Exploded View
INFOID:0000000009177402
Removal and Installation
INFOID:0000000009177403
REMOVAL
1. Apply matching marks to the rear suspension arms, the connecting rods, and the stabilizer shaft to identify
the installation position.
2. Remove both upper connecting rod nuts (A). Disconnect both
connecting rods from the rear suspension arms.
3. Remove the 4 stabilizer clamp bolts (A) using power tool.
4. Remove the stabilizer clamps.
5. Remove the stabilizer bar bushings.
1.
Rear suspension arm
2.
Connecting rod (LH)
3.
Stabilizer bar
4.
Stabilizer bar bushing
5.
Stabilizer bar clamp
Front
AWEIA0284ZZ
ALEIA0149ZZ
ALEIA0150ZZ
RSU-16
< REMOVAL AND INSTALLATION >
REAR STABILIZER
6. Remove the stabilizer bar.
7. Remove both lower connecting rod nuts. Disconnect both connecting rods from the stabilizer bar.
INSTALLATION
Installation is in the reverse order of removal.
• Position the stabilizer bar bushings with the slit facing the front of the vehicle.
• Align the matching marks when installing.
• Tighten the connecting rod nut to the specified torque while holding the hexagonal part of the connecting rod
stud.
REAR SUSPENSION ARM
RSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SUSPENSION ARM
Exploded View
INFOID:0000000009177404
Removal and Installation
INFOID:0000000009177405
REMOVAL
1. Remove the rear wheel and tire using power tool. Refer to
.
2. Remove the brake caliper torque member bolts, leaving the brake hose attached. Position the caliper
aside with wire. Refer to
BR-36, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
CAUTION:
Do not depress the brake pedal while the brake caliper is removed.
3. Put alignment marks on the disc brake rotor and on the wheel hub and bearing. Remove the disc brake
rotor.
1.
Rear suspension arm
2.
Connecting rod (LH)
3.
Rear suspension member
4.
Stabilizer bar
5.
Rear knuckle
Front
AWEIA0285ZZ
RSU-18
< REMOVAL AND INSTALLATION >
REAR SUSPENSION ARM
CAUTION:
Do not drop the disc brake rotor.
4. Remove the coil spring. Refer to
RSU-8, "Removal and Installation"
.
5. Remove the upper connecting rod nut. Disconnect the connecting rod from the rear suspension arm.
.
6. Remove the wheel sensor (1) and the wheel speed sensor har-
ness from the rear knuckle. Refer to
7. Remove the wheel speed sensor harness from rear suspension arm.
8. Remove the stabilizer bar. Refer to
.
9. Remove the suspension arm bolt and nut from the rear knuckle using power tool. Disconnect the suspen-
sion arm from the rear knuckle.
10. Remove the suspension arm bolts and nuts from the rear suspension member using power tool.
11. Remove the suspension arm.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse the rear suspension arm nuts at the rear suspension member.
• Perform the final tightening of the parts under unladen conditions with tires on the ground.
• Check the wheel sensor harness for proper connection. Refer to
BRC-119, "Exploded View - Rear Wheel
.
• Check the wheel alignment. Refer to
RSU-6, "Inspection and Adjustment"
.
• Adjust the neutral position of the steering angle sensor. Refer to
ALDIA0293ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст