Nissan Pathfinder. Manual — part 992
REAR SHOCK ABSORBER
RSU-11
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
5. Remove the rear shock absorber nuts (
).
6. Remove the rear shock absorber.
INSTALLATION
Installation is in the reverse order of removal.
• Perform the final tightening of the parts under unladen conditions with the tires on the ground.
Disposal
INFOID:0000000009177397
1. Set the shock absorber horizontally with the piston rod fully extended.
2. Drill a 2 – 3 mm (0.08 – 0.12 in) hole at the position ( ) as
shown to release gas gradually.
CAUTION:
• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-
pressed gas.
NOTE:
• Drill vertically in this direction (
) directly into the outer tube
avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.
3. Position the drilled hole downward and drain the oil by moving the piston rod several times.
CAUTION:
Dispose of drained oil according to the law and local regulations.
JPEIB0060ZZ
(A) : 20 – 30 mm (0.79 – 1.18 in)
JPEIA0161ZZ
RSU-12
< REMOVAL AND INSTALLATION >
RADIUS ROD
RADIUS ROD
Exploded View
INFOID:0000000009760274
Removal and Installation
INFOID:0000000009177399
REMOVAL
1. Remove the rear wheel and tire using power tool. Refer to
.
2. Remove the radius rod bolt and nut from the rear knuckle using power tool.
3. Remove the radius rod bolt from the rear suspension member using power tool.
4. Remove the radius rod.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse the radius rod nut.
1.
Rear suspension member
2.
Radius rod
3.
Rear knuckle
Front
AWEIA0315ZZ
FRONT LOWER LINK
RSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
FRONT LOWER LINK
Exploded View
INFOID:0000000009760275
Removal and Installation
INFOID:0000000009177401
REMOVAL
1. Remove the rear wheel and tire using power tool. Refer to
.
2. Support the rear lower link with a suitable jack.
WARNING:
Place a suitable jack under the outer end of the rear lower link.
CAUTION:
Do not damage the rear lower link with the suitable jack.
1.
Cap
2.
Shock absorber insulator
3.
Bound bumper
4.
Rear shock absorber
5.
Rear knuckle
6.
Front lower link
7.
Rear suspension member
Front
AWEIA0316ZZ
RSU-14
< REMOVAL AND INSTALLATION >
FRONT LOWER LINK
3. Support the rear knuckle with a suitable jack.
WARNING:
Place a suitable jack under the center of the rear knuckle.
CAUTION:
Do not damage the rear knuckle with the suitable jack.
4. Index mark the adjusting bolt to the rear suspension member.
5. Remove the lower shock absorber bolt using power tool. Refer to
6. Remove the coil spring. Refer to
RSU-8, "Removal and Installation"
.
7. Remove the front lower link bolt and nut from the rear suspension member using power tool.
8. Remove the front lower link bolt and nut from the rear knuckle using power tool.
9. Remove the front lower link cover.
10. Remove the front lower link.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse the front lower link nuts.
• Perform the final tightening of the parts under unladen conditions with the tires on the ground.
• Check the wheel alignment. Refer to
RSU-6, "Inspection and Adjustment"
.
• Adjust the neutral position of the steering angle sensor. Refer to
LEIA0008E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст