Nissan Pathfinder. Manual — part 849
CHASSIS AND BODY MAINTENANCE
MA-35
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
CAUTION:
Do not start engine while checking oil level.
1. Remove filler plug (1).
2. Oil level (A) should be level with bottom of filler plug hole. Add
oil if necessary. Refer to
(United States and Canada) or
"FOR MEXICO : Fluids and Lubricants"
3. Clean threads of filler plug (1) and transfer case.
4. Apply sealant to the threads of the filler plug (1) and install it.
Tighten to specified torque. Refer to
Use Genuine Silicone RTV Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
TRANSFER OIL : Draining
INFOID:0000000009174192
CAUTION:
Do not start engine while checking oil level.
1. Run the vehicle to warm up the transfer unit sufficiently.
2. Stop the engine and remove drain plug (1) and drain the transfer
oil.
3. Clean threads of drain plug (1) and transfer case.
4. Apply sealant to the threads of the drain plug (1) and install it.
Tighten to specified torque. Refer to
Use Genuine Silicone RTV Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
TRANSFER OIL : Refilling
INFOID:0000000009174193
CAUTION:
Do not start engine while checking oil level.
1. Remove filler plug (1).
2. Fill with new oil to the specified level near the filler plug hole.
3. Clean threads of filler plug (1) and transfer case.
4. Apply sealant to the threads of the filler plug (1), and install it. Tighten to specified torque. Refer to
Use Genuine Silicone RTV Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Prod-
.
: Front
ALDIA0383ZZ
: Front
ALDIA0382ZZ
: Front
Oil grade and viscosity
: Refer to
USA AND CANADA : Flu-
ids and Lubricants"
(Unit-
ed States and Canada) or
MA-16, "FOR MEXICO :
Fluids and Lubricants"
(Mexico).
Oil capacity
: Refer to
.
ALDIA0383ZZ
MA-36
< PERIODIC MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
REAR DIFFERENTIAL GEAR OIL
REAR DIFFERENTIAL GEAR OIL : Inspection
INFOID:0000000009174194
OIL LEAKS
Check that oil is not leaking from final drive assembly or around it.
OIL LEVEL
CAUTION:
Do not start engine while checking oil level.
1. Remove and discard filler plug (1).
CAUTION:
Do not reuse filler plug.
2. oil level should be level with the bottom of filler plug hole. add oil
if necessary. refer to
MA-15, "FOR USA AND CANADA : Fluids
(United States and Canada) or
MEXICO : Fluids and Lubricants"
3. install filler plug (1) and tighten to specified torque. refer to
REAR DIFFERENTIAL GEAR OIL : Draining
INFOID:0000000009174195
CAUTION:
Do not start engine while checking oil level.
1. Remove and discard drain plug (1), and drain gear oil.
CAUTION:
Do not reuse drain plug.
2. Install drain plug (1) and tighten to specified torque. Refer to
.
REAR DIFFERENTIAL GEAR OIL : Refilling
INFOID:0000000009174196
CAUTION:
Do not start engine while checking oil level.
1. Remove and discard filler plug (1).
CAUTION:
Do not reuse filler plug.
2. Fill with new oil to the specified level near the filler plug hole.
: Front
ALDIA0275ZZ
: Front
ALDIA0277ZZ
: Front
ALDIA0275ZZ
CHASSIS AND BODY MAINTENANCE
MA-37
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
3. Install filler plug (1) and tighten to specified torque. Refer to
.
PROPELLER SHAFT
PROPELLER SHAFT : Inspection
INFOID:0000000009174197
APPEARANCE AND NOISE INSPECTION
• Inspect the propeller shaft tube for dents or cracks. If damaged, replace the propeller shaft assembly.
• Check bearings for noise or damage. If damaged, replace as necessary.
WHEELS
WHEELS : Inspection
INFOID:0000000009174198
1. Check tires for wear and improper inflation.
2. Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.
3. Remove tire from wheel and mount wheel on a tire balance
machine.
CAUTION:
DO NOT use center hole cone-type clamping machines to
hold the wheel assembly during tire removal/installation or
balancing or damage to the wheel paint, cladding or chrome
may result. Use only rim-type or universal lug-type clamp-
ing machines to hold the wheel assembly during servicing.
a. Set dial indicator as shown.
b. Check runout, if the lateral runout (A) or radial runout (B)
exceeds the limit, replace wheel.
WHEELS : Adjustment
INFOID:0000000009174199
BALANCING WHEELS (ADHESIVE WEIGHT TYPE)
Preparation Before Adjustment
Remove inner and outer balance weights from the road wheel. Using releasing agent, remove double-faced
adhesive tape from the road wheel.
CAUTION:
• Be careful not to scratch the road wheel during removal.
• After removing double-faced adhesive tape, wipe clean all traces of releasing agent from the road
wheel.
Wheel Balance Adjustment
Oil grade and viscosity
: Refer to
USA AND CANADA : Flu-
ids and Lubricants"
(Unit-
ed States and Canada) or
MA-16, "FOR MEXICO :
Fluids and Lubricants"
(Mexico).
Oil capacity
: Refer to
Lateral runout (A)
Radial runout (B)
SEIA0737E
MA-38
< PERIODIC MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
• If a balancer machine has an adhesive weight mode setting, select the adhesive weight mode setting and
skip Step 2 below. If a balancer machine only has the clip-on (rim flange) weight mode setting, follow Step 2
to calculate the correct size adhesive weight.
1. Set road wheel on balancer machine using the center hole as a guide. Start the balancer machine.
2. For balancer machines that only have a clip-on (rim flange) weight mode setting, follow this step to calcu-
late the correct size adhesive weight to use. When inner and outer imbalance values are shown on the
balancer machine indicator, multiply outer imbalance value by 5/3 (1.67) to determine balance weight that
should be used. Select the outer balance weight with a value closest to the calculated value above and
install in to the designated outer position of or at the designated angle in relation to the road wheel.
a. Indicated imbalance value
× 5/3 = balance weight to be installed
Calculation example:
23 g (0.81 oz)
× 5/3 (1.67) = 38.33 g (1.35 oz) ⇒ 40 g (1.41 oz)
balance weight (closer to calculated balance weight value)
NOTE:
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4
⇒ 35 g (1.23 oz)
37.5
⇒ 40 g (1.41 oz)
3. Install balance weight in the position shown.
CAUTION:
• Do not install the inner balance weight before installing
the outer balance weight.
• Before installing the balance weight, be sure to clean the
mating surface of the road wheel.
• When installing balance weight (1) to road wheel, set it into the
grooved area (A) on the inner wall of the road wheel as shown
so that the balance weight center (B) is aligned with the bal-
ancer machine indication position (angle) (C).
CAUTION:
• Always use genuine NISSAN adhesive balance weights.
• Balance weights are non-reusable; always replace with
new ones.
• Do not install more than three sheets of balance
weights.
4. If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other as shown.
CAUTION:
Do not install one balance weight sheet on top of another.
5. Start balancer machine again.
6. Install balance weight on inner side of road wheel in the bal-
ancer machine indication position (angle).
CAUTION:
Do not install more than two balance weights.
7. Start balancer machine. Make sure that inner and outer residual
imbalance values are 5 g (0.17 oz) each or below.
8. If either residual imbalance value exceeds 5 g (0.17 oz), repeat installation procedures.
SMA054D
JPEIC0040ZZ
PEIA0033E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст