Nissan Pathfinder. Manual — part 1033
SE-130
< UNIT DISASSEMBLY AND ASSEMBLY >
SECOND ROW SEAT
14. Remove the seatback pad and seatback trim (1).
a. Release the J-clip retainer (
) at the rear lower edge of seat-
back.
b. Remove two clips that retain seatback trim in place.
: Clip
c.
Remove two hog rings that retain seatback pad in place.
NOTE:
Remove all pieces of hog rings and discard them.
: Hog ring
d. Release retainer strips (A) from the seat frame assembly (2).
e. Release clips that retain trim behind EZ entry finisher.
f.
Remove the seatback pad and seatback trim as an assembly from the seat frame assembly.
15. Reach up behind the seatback pad, release the headrest holder
locks as shown and remove the headrest holders.
CAUTION:
Before removing/installing headrest holder, check its orien-
tation (front/rear and right/left).
16. Separate the seatback trim (1) from the seatback pad.
a. Pull seatback trim upward in front to release hook fasteners (A).
b. Remove hog rings and separate the seatback trim from the seat-
back pad.
NOTE:
Remove all pieces of hog rings and discard them.
: Hog ring
c.
Route the seatback heater harness (if equipped) through the
opening in the seatback trim.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Install new hog rings on the seatback trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat-
back trim and seatback pad wires.
• Use NISSAN standard hog rings and tools to assemble.
• Make sure hook fastener is pressed into place after seatback trim
is assembled.
• Smooth out all wrinkles during assembled.
RH SEAT : Seat Cushion
INFOID:0000000009727796
DISASSEMBLY
1. Remove RH seat cushion. Refer to
2. Remove support strut from RH seat cushion.
ALJIA0870ZZ
JMJIA4073ZZ
ALJIA0872ZZ
PIIB3356J
SECOND ROW SEAT
SE-131
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
3. Remove the seat cushion pad and seat cushion trim (1).
a. Unzip the back trim cover and release the J-clip retainer (
).
b. Remove the seat cushion pad and seat cushion trim as an
assembly from the seat cushion frame (2).
4. Separate the seat cushion trim (1) from the seat cushion pad.
a. Remove hog rings and separate the seat cushion trim from the
seat cushion pad.
NOTE:
Remove all pieces of hog rings and discard them.
: Hog ring
: Front
b. Route the seat cushion heater harness (if equipped) through the
opening in the seat cushion trim.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Install new hog rings on the seat cushion trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat
cushion trim and seat cushion pad wires.
• Use NISSAN standard hog rings and tools to assemble.
ALJIA0875ZZ
ALJIA0873ZZ
PIIB3356J
SE-132
< UNIT DISASSEMBLY AND ASSEMBLY >
THIRD ROW SEAT
THIRD ROW SEAT
Exploded View
INFOID:0000000009727797
Seatback
INFOID:0000000009727798
SEATBACK
Disassembly
1. Remove the third row seat. Refer to
SE-107, "Removal and Installation"
.
2. Release the pawls and remove the tether anchor finisher.
3. Remove the screw and the seatback cargo hook.
4. Press both headrest holder lock buttons in and lift headrest up, and remove.
1.
Seatback release lever and cable
(LH/RH)
2.
Seatback release lever finisher (LH/
RH)
3.
Headrest (LH)
4.
Headrest (RH)
5.
Headrest holders (RH)
6.
Headrest holders (LH)
7.
Seatback trim (RH)
8.
Seatback pad (RH)
9.
Seatback trim (LH)
10. Seatback pad (LH)
11. Seat cushion trim
12. Seat cushion pad
13. Seat belt buckle (RH)
14. Seat hinge finisher (center)
15. Seat bolt finisher
16. Seat belt buckle (LH)
17. Seat frame assembly
18. Seat hinge finisher (LH)
19. Seatback board (LH)
20. Seatback pull strap (LH)
21. Seatback cargo hook
22. Tether anchor finisher
23. Seatback pull strap (RH)
24. Seatback board (RH)
25. Seatback hinge finisher (RH)
AWJIA1017ZZ
THIRD ROW SEAT
SE-133
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
5. Remove the seatback board.
NOTE:
Backside of seatback board shown for clarity.
a. Release the hook fastener (A) along the upper edge.
b. Release three clips (B) that retain the seatback board to the seat
frame assembly.
c. Release the remaining clips in the order shown.
6. Remove the seatback trim and seatback pad.
a. Release retainer strip (A) from the seat frame assembly slots (B)
on the top edge of the seat frame assembly.
b. Repeat at the lower and LH/RH edges.
c. Reach up behind the seatback pad, release the headrest holder
locks as shown and remove the headrest holders.
CAUTION:
Before removing/installing headrest holder, check its orien-
tation (front/rear and right/left).
d. Remove the seatback pad and seatback trim as an assembly from the seat frame assembly.
7. Separate the seatback trim from the seatback pad.
a. Pull seatback trim upward in front to release hook fasteners (A).
b. Remove hog rings and separate the seatback trim from the seat-
back pad.
NOTE:
Remove all pieces of hog rings and discard them.
: Hog ring
8. Remove the screw and the seatback pull strap.
ALJIA0840ZZ
ALJIA0841ZZ
JMJIA4073ZZ
ALJIA0836ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст