Nissan Pathfinder. Manual — part 265
WHEEL SENSOR
BRC-119
< UNIT REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
Installation is in the reverse order of removal.
CAUTION:
• When installing, make sure there is no foreign material such as iron chips on and in the hole in the
steering knuckle for the front wheel sensor. Make sure no foreign material has been caught in the
sensor rotor. Remove any foreign material and clean the mount.
• Do not twist front wheel sensor harness when installing front
wheel sensor. Check that grommet (2) is fully inserted to
bracket (1). Check that front wheel sensor harness is not
twisted after installation.
Exploded View - Rear Wheel Sensor
INFOID:0000000009177350
RH Side
JPFIC0209ZZ
ALFIA0263GB
1.
Rear wheel sensor
A. Rear wheel sensor bracket
B. Clip
C. Rear wheel sensor connector
Front
BRC-120
< UNIT REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
WHEEL SENSOR
LH Side
Removal and Installation - Rear Wheel Sensor
INFOID:0000000009177351
CAUTION:
• Be careful not to damage rear wheel sensor edge and sensor rotor teeth.
• When removing the rear wheel hub and bearing, first remove the rear wheel sensor from the rear
knuckle. Failure to do so may result in damage to the rear wheel sensor wires making the rear wheel
sensor inoperative.
• Pull out the rear wheel sensor, being careful to turn it as little as possible. Do not pull on the rear
wheel sensor harness.
• Before installation, check if foreign objects such as iron fragments are adhered to the pick-up part of
the rear wheel sensor or to the inside of the hole in the rear knuckle for the rear wheel sensor, or if a
foreign object is caught in the surface of the mating surface for the sensor rotor. Fix as necessary
and then install the rear wheel sensor.
REMOVAL
1. Remove the rear wheel and tire using power tool. Refer to
.
2. Remove the rear wheel sensor bolt.
3. Disconnect the harness connector from the rear wheel sensor.
4. Remove the rear wheel sensor from the sensor brackets.
5. Remove the rear wheel sensor from the rear knuckle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
ALFIA0264GB
1.
Rear wheel sensor
A. Rear wheel sensor connector
B. Clip
C. Rear wheel sensor bracket
Front
WHEEL SENSOR
BRC-121
< UNIT REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• When installing, make sure there is no foreign material such as iron chips on and in the hole in the
rear knuckle for the rear wheel sensor. Make sure no foreign material has been caught in the sensor
rotor. Remove any foreign material and clean the mount.
• Do not twist rear wheel sensor harness when installing rear
wheel sensor. Check that grommet (2) is fully inserted to
bracket (1). Check that rear wheel sensor harness is not
twisted after installation.
JPFIC0209ZZ
BRC-122
< UNIT REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
SENSOR ROTOR
SENSOR ROTOR
Removal and Installation - Front Sensor Rotor
INFOID:0000000009177352
The front wheel sensor rotor is an integral part of the wheel hub and bearing and cannot be disassembled.
FAX-8, "Removal and Installation"
Removal and Installation - Rear Sensor Rotor
INFOID:0000000009177353
The rear wheel sensor rotor is an integral part of the wheel hub and bearing and cannot be disassembled.
RAX-7, "Removal and Installation"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст