Nissan Pathfinder. Manual — part 628
BACK DOOR OUTER FINISHER
EXT-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
BACK DOOR OUTER FINISHER
Exploded View
INFOID:0000000009176361
Removal and Installation
INFOID:0000000009176362
REMOVAL
1. Remove the back door lower finisher. Refer to
INT-35, "BACK DOOR LOWER FINISHER : Removal and
.
2. Disconnect the harness connectors from rear view camera and back door opener switch.
3. Remove the back door outer finisher nuts.
4. Release the clips, then remove the back door outer finisher.
5. Remove the following parts (if necessary) after removing back door outer finisher.
• Rear view camera
• Back door opener switch
• License plate lamp
INSTALLATION
Installation is in the reverse order of removal.
1.
Back door outer finisher
2.
Rear camera
3.
Back door opener request switch
Clip
AWKIA2640ZZ
FAX-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
FAX
A
B
FAX
N
O
P
CONTENTS
FRONT AXLE
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Drive Shaft . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
FRONT WHEEL HUB . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . ..
FRONT DRIVE SHAFT . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
FRONT WHEEL HUB . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
FRONT DRIVE SHAFT BOOT . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
WHEEL SIDE . . . . . . . . . . . . . . . .
WHEEL SIDE : Removal and Installation . . . .
TRANSAXLE SIDE . . . . . . . . . . . . .
TRANSAXLE SIDE : Removal and Installation . ...
Inspection . . . . . . . . . . . . . . . .
FRONT DRIVE SHAFT . . . . . . . . . .
Exploded View (LH) . . . . . . . . . . . . .
Removal and Installation (LH) . . . . . . . . .
Exploded View (RH) . . . . . . . . . . . .
Removal and Installation (RH) . . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY .
FRONT DRIVE SHAFT . . . . . . . . . .
Disassembly and Assembly (LH) . . . . . . . .
Disassembly and Assembly (RH) . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Bearing . . . . . . . . . . . . . . .
Drive Shaft . . . . . . . . . . . . . . . ...
Dynamic Damper . . . . . . . . . . . . . .
FAX-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009725687
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precautions for Drive Shaft
INFOID:0000000009177835
Observe the following precautions when disassembling and assembling drive shaft.
• Joint sub-assembly does not disassemble because it is non-overhaul parts.
• Perform work in a location which is as dust-free as possible.
• Before disassembling and assembling, clean the outside of parts.
• Prevention of the entry of foreign objects must be taken into account during disassembly of the service loca-
tion.
• Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a clean cover
must be placed over parts.
• Paper shop cloths must be used. Fabric shop cloths must not be used because of the danger of lint adhering
to parts.
• Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be removed by
blowing with air or wiping with paper shop cloths.
PREPARATION
FAX-3
< PREPARATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009177836
The actual shapes of Kent-More tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000009177837
Tool number
(Kent-More No.)
Tool name
Description
KV40107300
( — )
Boot band crimping tool
Installing boot band
KV40107500
( — )
Drive shaft attachment
Removing drive shaft
KV38107900
( — )
Protector
a: 32 mm (1.26 in) dia.
Installing drive shaft
ZZA1229D
ZZA1230D
PDIA1183J
Tool name
Description
Drive shaft puller
Removing drive shaft joint sub assembly
JPDIG0152ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст