Nissan Pathfinder. Manual — part 627

DOOR OUTSIDE LOWER MOLDING

EXT-39

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

Installation is in the reverse order of removal.

CAUTION:

• When installing, visually check the outside lower molding and the clips and replace with new parts if

they have been damaged.

• When installing outside lower molding, make sure that the clips are attached to the molding. Make

sure old clips have all been removed from fender.

FRONT DOOR OUTSIDE LOWER MOLDING

Removal

1. Release the clips from the front door outside lower molding (1)

by starting at the rear and moving forward, using a suitable tool

(A).

CAUTION:

• Apply protective tape (B) to the door to protect the

painted surface from damage.

• Release the clips slowly and carefully.

• Do not pull the front door outside lower molding.

2. Remove the front door outside lower molding.

Installation

Installation is in the reverse order of removal.

CAUTION:

• When installing, visually check the outside lower molding and the clips and replace with new parts if

they have been damaged.

• When installing outside lower molding, make sure that the clips are attached to the molding. Make

sure old clips have all been removed from door.

REAR DOOR OUTSIDE LOWER MOLDING

Removal

1. Release the clips from the rear door outside lower molding (1)

by starting at the rear and moving forward, using a suitable tool

(A).

CAUTION:

• Apply protective tape (B) to the door to protect the

painted surface from damage.

• Release the clips slowly and carefully.

• Do not pull the rear door outside lower molding.

2. Remove the rear door outside lower molding.

Installation

Installation is in the reverse order of removal.

CAUTION:

• When installing, visually check the outside lower molding and the clips and replace with new parts if

they have been damaged.

• When installing outside lower molding, make sure that the clips are attached to the molding. Make

sure old clips have all been removed from door.

ALKIA2492ZZ

ALKIA2493ZZ

EXT-40

< REMOVAL AND INSTALLATION >

SILL MOLDING

SILL MOLDING

Exploded View

INFOID:0000000009176357

Removal and Installation

INFOID:0000000009176358

REMOVAL

1. Release sill molding clips with a suitable tool (A), then remove

the sill molding (1).

CAUTION:

Disengage the clips slowly and carefully.

: Clip

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• When installing, visually check the sill molding and the clips and replace them with new parts if they

have been damaged.

• When installing the sill molding, check that clips are securely placed in panel holes on body, then

press them in.

1. Sill molding

A. Clip

AWKIA2136ZZ

ALKIA2511ZZ

REAR SPOILER

EXT-41

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

REAR SPOILER

Exploded View

INFOID:0000000009176359

Removal and Installation

INFOID:0000000009176360

REMOVAL

1. Remove the back door side finishers (LH/RH). Refer to

EXT-43, "Removal and Installation"

.

2. Remove the rear spoiler nuts.
3. Disconnect the harness connector from high-mounted stop lamp.
4. Release the rear washer nozzle tube.
5. Release the rear spoiler clips with a suitable tool (A), and then

remove the rear spoiler.

CAUTION:

Apply protective tape (B) to the roof panel and rear spoiler

to protect the painted surface from damage.

: Clip

6. Remove following parts (if necessary) after removing rear spoiler.

• High-mounted stop lamp

• Rear spoiler side trim covers (LH/RH)

• Rear washer nozzle

1.

Rear spoiler

2.

Rear spoiler side trim cover
(LH/RH)

3.

High-mounted stop lamp

4.

Rear washer nozzle

Clip

AWKIA2639ZZ

ALKIA2512ZZ

EXT-42

< REMOVAL AND INSTALLATION >

REAR SPOILER

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• When installing, visually check the rear spoiler and the clips and replace them with new parts if they

are damaged.

• When installing, make sure that the clips and bolts are securely placed in back door panel holes, and

then press them in.

• Do not wash the vehicle within 24 hours after installing to allow adhesive time to cure.