Nissan Pathfinder. Manual — part 1182
CVT FLUID
TM-187
< PERIODIC MAINTENANCE >
[CVT: RE0F10E]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
34. Select “Data Monitor” in “TRANSMISSION” using CONSULT.
35. Select “CONFORM CVTF DETERIORTN”.
36. Select “Erase”.
37. Stop the engine.
Adjustment
INFOID:0000000009177645
CAUTION:
• During adjustment of the CVT fluid level, check CONSULT so that the oil temperature may be main-
tained from 35 to 45
°C (95 to 113°F).
• During adjustment of the CVT fluid level, check that the engine speed is maintaining 500 rpm.
• Use caution when looking into the drain hole as there is a risk of dripping fluid entering the eye.
1. Check that the selector lever is in the “P” position, then completely engage the parking brake.
2. Start the engine.
3. Adjust the CVT fluid temperature to be approximately 40
°C (104°F).
NOTE:
The CVT fluid is largely affected by temperature. Therefore be sure to use CONSULT and check the
“FLUID TEMP” under “TRANSMISSION” in “Data Monitor” while adjusting.
4. While depressing the brake pedal, shift the selector lever to the entire position from “P” to “L”, and shift it
to the “P” position.
NOTE:
Hold the lever at each position for 5 seconds.
5. Lift up the vehicle.
6. Check that there is no CVT fluid leakage.
7. Remove the overflow plug from converter housing.
8. Install the charging pipe set (KV311039S0) (A) into the overflow
plug hole.
CAUTION:
Tighten the charging pipe by hand.
9. Install the ATF changer hose (B) to the charging pipe.
CAUTION:
Press the ATF changer hose all the way onto the charging
pipe until it stops.
10. Fill approximately 0.5 liter (1/2 US qt, 1/2 lmp qt) of the CVT
fluid.
11. Remove the ATF changer hose from the charging pipe, and
check that the CVT fluid drains out from the charging pipe. If it
does not drain out, perform charging again.
CAUTION:
Perform this work with the vehicle idling.
12. When the flow of CVT fluid slows to a drip, remove the charging pipe from the converter housing.
13. Tighten the overflow plug to the specified torque. Refer to
.
CAUTION:
CVT fluid
: Refer to
TM-219, "General Specification"
Fluid capacity
: Refer to
TM-219, "General Specification"
: Vehicle front
JSDIA3714ZZ
JSDIA3713ZZ
TM-188
< PERIODIC MAINTENANCE >
[CVT: RE0F10E]
CVT FLUID
Never reuse O-ring.
14. Lift down the vehicle.
15. Stop the engine.
CVT SHIFT SELECTOR
TM-189
< REMOVAL AND INSTALLATION >
[CVT: RE0F10E]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION
CVT SHIFT SELECTOR
Exploded View
INFOID:0000000009177646
Removal and Installation
INFOID:0000000009177647
REMOVAL
1. Apply the parking brake.
CAUTION:
Make sure the vehicle cannot move with the parking brake applied.
2. Remove shift lock override button cover (1) using suitable tool,
and insert suitable tool into opening to depress the shift lock
override button. Move shift selector to "N" position while
depressing shift lock override button.
: Front
1.
CVT shift selector assembly
2.
Control cable
3.
Shift selector handle cover
4
Shift selector handle
A.
Shift selector handle clip
AWDIA1064ZZ
ALDIA0393ZZ
TM-190
< REMOVAL AND INSTALLATION >
[CVT: RE0F10E]
CVT SHIFT SELECTOR
3. Remove the shift selector handle (1).
a. Release the shift selector handle cover (2) using a suitable tool
from the base of the shift selector handle (1).
b. Remove the shift selector handle clip (A).
c.
Pull upward and remove the shift selector handle (1).
4. Remove center console upper side finisher (LH). Refer to
.
5. Release center console side finisher (LH/RH) clip and pawls
using a suitable tool and remove.
: Clip
: Pawl
: Front
6. Release shift selector finisher clips and pawls using a suitable tool, disconnect the harness connectors
and remove. Refer to
7. Release the harness clip, then disconnect the harness connector from shift selector.
8. Remove the control cable from the shift selector assembly. Refer to
TM-191, "Removal and Installation"
.
9. Remove the four shift selector assembly nuts and the shift selector assembly from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
• When installing control cable (1) to the shift selector assembly (2),
check that control cable is fully pressed in until it stops with the
ribbed surface (A) facing upward.
NOTE:
Apply multi-purpose grease to control cable eye before installation.
• Adjust control cable as necessary. Refer to
Inspection
INFOID:0000000009177648
INSPECTION
Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to
.
ALDIA0353ZZ
ALJIA1257ZZ
JSDIA1624ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст