Nissan Pathfinder. Manual — part 27
ADP-100
< DTC/CIRCUIT DIAGNOSIS >
LIFTING SWITCH (REAR)
LIFTING SWITCH (REAR)
Description
INFOID:0000000009176594
Lifting switch (rear) is equipped to the power seat switch LH on the seat frame. The operation signal is inputted
to the driver seat control unit when the lifting switch (rear) is operated.
Component Function Check
INFOID:0000000009176595
1.
CHECK FUNCTION
1. Select “LIFT RR SW-UP”, “LIFT RR SW-DN” in “DATA MONITOR” mode with CONSULT.
2. Check lifting switch (rear) signal under the following conditions.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Perform diagnosis procedure. Refer to
ADP-100, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009176596
Regarding Wiring Diagram information, refer to
ADP-55, "WITH AROUND VIEW MONITOR : Wiring Diagram"
or
ADP-40, "WITHOUT AROUND VIEW MONITOR : Wiring Diagram"
.
1.
CHECK LIFTING SWITCH (REAR) SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK LIFTING SWITCH (REAR) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and power seat switch LH.
3. Check continuity between driver seat control unit harness connector and power seat switch LH harness
connector.
Monitor item
Condition
Status
LIFT RR SW-UP
Lifting switch rear (up)
Operate
ON
Release
OFF
LIFT RR SW-DN
Lifting switch rear (down)
Operate
ON
Release
OFF
(+)
(–)
Condition
Voltage (V)
(Approx.)
Driver seat control unit
Connector
Termi-
nals
B209
6
Ground
Lifting
switch
(rear)
Operate (down)
0
Release
Battery voltage
22
Operate (up)
0
Release
Battery voltage
LIFTING SWITCH (REAR)
ADP-101
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
4. Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK DRIVER SEAT CONTROL UNIT OUTPUT
1. Connect the driver seat control unit.
2. Turn ignition switch ON.
3. Check voltage between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace driver seat control unit. Refer to
ADP-161, "Removal and Installation"
4.
CHECK LIFTING SWITCH (REAR)
ADP-101, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace power seat switch LH. Refer to
ADP-164, "Removal and Installation"
5.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace driver seat control unit. Refer to
ADP-161, "Removal and Installation"
NO
>> Repair or replace the malfunctioning part.
Component Inspection
INFOID:0000000009176597
1.
CHECK LIFTING SWITCH (REAR)
1. Turn ignition switch OFF.
2. Disconnect power seat switch LH.
3. Check continuity between power seat switch LH terminals.
Driver seat control unit
Power sear switch LH
Continuity
Connector
Terminal
Connector
Terminal
B209
6
B208
2
Yes
22
1
Driver seat control unit
Ground
Continuity
Connector
Terminal
B209
6
No
22
(+)
(–)
Voltage (V)
(Approx.)
Driver seat control unit
Connector
Terminals
B209
6
Ground
Battery voltage
22
ADP-102
< DTC/CIRCUIT DIAGNOSIS >
LIFTING SWITCH (REAR)
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace power seat switch LH. Refer to
ADP-164, "Removal and Installation"
Terminal
Condition
Continuity
Power seat switch LH
3
1
Lifting switch rear (up)
Operate
Yes
Release
No
2
Lifting switch rear (down)
Operate
Yes
Release
No
TILT SWITCH
ADP-103
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
TILT SWITCH
Description
INFOID:0000000009176598
ADP steering switch (tilt switch) is equipped to the steering column. The operation signal is input to the auto-
matic drive positioner control unit when the ADP steering switch is operated.
Component Function Check
INFOID:0000000009176599
1.
CHECK FUNCTION
1. Select “TILT SW-UP”, “TILT SW-DOWN” in “DATA MONITOR” mode with CONSULT.
2. Check tilt switch signal under the following conditions.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Perform diagnosis procedure. Refer to
ADP-103, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009176600
Regarding Wiring Diagram information, refer to
ADP-55, "WITH AROUND VIEW MONITOR : Wiring Diagram"
ADP-40, "WITHOUT AROUND VIEW MONITOR : Wiring Diagram"
1.
CHECK TILT SWITCH SIGNAL
1. Disconnect ADP steering switch (tilt switch).
2. Check voltage between ADP steering switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK TILT SWITCH CIRCUIT
1. Disconnect automatic drive positioner control unit.
2. Check continuity between automatic drive positioner control unit harness connector and ADP steering
switch harness connector.
3. Check continuity between automatic drive positioner control unit harness connector and ground.
Monitor item
Condition
Status
TILT SW-UP
Tilt switch (up)
Operate
ON
Release
OFF
TILT SW-DOWN
Tilt switch (down)
Operate
ON
Release
OFF
(+)
(–)
Voltage (V)
(Approx.)
ADP steering switch (tilt switch)
Connector
Terminals
M16
2
Ground
Battery voltage
5
Automatic drive positioner control
unit
ADP steering switch (tilt switch)
Continuity
Connector
Terminal
Connector
Terminal
M33
1
M16
5
Yes
13
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст