Nissan Pathfinder. Manual — part 26
ADP-96
< DTC/CIRCUIT DIAGNOSIS >
RECLINING SWITCH
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace power seat switch LH. Refer to
ADP-164, "Removal and Installation"
Terminals
Condition
Continuity
Power seat switch LH
3
10
Reclining switch
(backward)
Operate
Yes
Release
No
9
Reclining switch
(forward)
Operate
Yes
Release
No
LIFTING SWITCH (FRONT)
ADP-97
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
LIFTING SWITCH (FRONT)
Description
INFOID:0000000009176590
Lifting switch (front) is equipped to the power seat switch LH on the seat frame. The operation signal is input to
the driver seat control unit when the lifting switch (front) is operated.
Component Function Check
INFOID:0000000009176591
1.
CHECK FUNCTION
1. Select “LIFT FR SW-UP”, “LIFT FR SW-DN” in “DATA MONITOR” mode with CONSULT.
2. Check lifting switch (front) signal under the following conditions.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Perform diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000009176592
Regarding Wiring Diagram information, refer to
ADP-55, "WITH AROUND VIEW MONITOR : Wiring Diagram"
ADP-40, "WITHOUT AROUND VIEW MONITOR : Wiring Diagram"
1.
CHECK LIFTING SWITCH SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK LIFTING SWITCH (FRONT) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and power seat switch LH.
3. Check continuity between driver seat control unit harness connector and power seat switch LH harness
connector.
Monitor item
Condition
Status
LIFT FR SW-UP
Lifting switch front (up)
Operate
ON
Release
OFF
LIFT FR SW-DN
Lifting switch front (down)
Operate
ON
Release
OFF
(+)
(–)
Condition
Voltage (V)
(Approx.)
Driver seat control unit
Connector
Termi-
nals
B209
7
Ground
Lifting
switch
(front)
Operate
(down)
0V
Release
Battery
voltage
23
Operate (up)
0V
Release
Battery
voltage
ADP-98
< DTC/CIRCUIT DIAGNOSIS >
LIFTING SWITCH (FRONT)
4. Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK DRIVER SEAT CONTROL UNIT OUTPUT
1. Connect the driver seat control unit.
2. Turn ignition switch ON.
3. Check voltage between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace driver seat control unit. Refer to
ADP-161, "Removal and Installation"
4.
CHECK LIFTING SWITCH (FRONT)
ADP-98, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace power seat switch LH. Refer to
ADP-164, "Removal and Installation"
5.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace driver seat control unit. Refer to
ADP-161, "Removal and Installation"
NO
>> Repair or replace the malfunctioning part.
Component Inspection
INFOID:0000000009176593
1.
CHECK LIFTING SWITCH (FRONT)
1. Turn ignition switch OFF.
2. Disconnect power seat switch LH.
3. Check continuity between power seat switch LH terminals.
Driver seat control unit
Power seat switch LH
Continuity
Connector
Terminal
Connector
Terminal
B209
7
B208
6
Yes
23
5
Driver seat control unit
Ground
Continuity
Connector
Terminal
B209
7
No
23
(+)
(–)
Voltage (V)
(Approx.)
Driver seat control unit
Connector
Terminals
B209
7
Ground
Battery voltage
23
LIFTING SWITCH (FRONT)
ADP-99
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace power seat switch LH. Refer to
ADP-164, "Removal and Installation"
Terminal
Condition
Continuity
Power seat switch LH
3
6
Lifting switch front (down)
Operate
Yes
Release
No
5
Lifting switch front (up)
Operate
Yes
Release
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст