Nissan Pathfinder. Manual — part 976
SYSTEM
RF-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
• Door CLOSE (door switch OFF)
→OPEN (door switch ON).
• When ignition switch is ON again.
• When timer time passes (45 seconds).
ANTI-PINCH FUNCTION
The moonroof motor’s built in CPU monitors the moonroof motor operation and position.
If a restriction is detected during the slide closed or tilt down operation the moonroof motor will move the glass
in the open positions. The moonroof will operate until full up position (when tilt down operates) or 125 mm
(4.92 in.) or more in the open direction.
SUNSHADE
SUNSHADE : System Diagram
INFOID:0000000009176279
SUNSHADE
SUNSHADE : System Description
INFOID:0000000009176280
DESCRIPTION
• The BCM supplies power to the sunshade motor assembly while the ignition is ON or retained power is oper-
ating.
• The sunshade switch can be operated in the directions of open (1) and close (2).
AUTO OPERATION
AWKIA1976ZZ
AWKIA1977ZZ
RF-10
< SYSTEM DESCRIPTION >
SYSTEM
Sunshade moves to the fully-open or fully-close position by pressing and releasing the sunshade switch.
OPEN (1) or CLOSE (2) position.
RETAINED POWER OPERATION
Retained power operation is an additional power supply function that enables the sunshade system to operate
for 45 seconds after ignition switch is turned OFF.
Retained power function cancel conditions
• Front door CLOSE (door switch OFF)
→OPEN (door switch ON)
• Ignition switch is ON again.
• Timer passed (45 seconds)
ANTI-PINCH FUNCTION
CAUTION:
There are some small distances immediately before the closed position which cannot be detected.
• The CPU is built inside the sunshade motor assembly. It monitors the sunshade condition by the signals
from sunshade motor. When the sunshade motor assembly detects an interruption during auto close opera-
tion, a signal is sent to the CPU to open the sunshade.
DIAGNOSIS SYSTEM (BCM)
RF-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000009763999
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF
→ ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentially causing a discharged battery and no-start condition.
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Direct Diagnostic Mode
Description
Ecu Identification
The BCM part number is displayed.
Self Diagnostic Result
The BCM self diagnostic results are displayed.
Data Monitor
The BCM input/output data is displayed in real time.
Active Test
The BCM activates outputs to test components.
Work support
The settings for BCM functions can be changed.
Configuration
• The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing BCM.
CAN Diag Support Mntr
The result of transmit/receive diagnosis of CAN communication is displayed.
System
Sub System
Direct Diagnostic Mode
Ecu I
de
nti
ficat
ion
Se
lf Di
ag
no
sti
c
Res
ult
Dat
a Monitor
Active T
e
st
W
ork su
pp
ort
Co
nf
ig
ur
at
io
n
CAN Diag
Su
pp
ort
Mn
tr
Door lock
DOOR LOCK
×
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEADLAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps FLASHER
×
×
Air conditioner
AIR CONDITIONER
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
×
Combination switch
COMB SW
×
BCM
BCM
×
×
×
×
×
Immobilizer
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
Back door open
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
RF-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
RETAINED PWR
RETAINED PWR : CONSULT Function (BCM - RETAINED PWR)
INFOID:0000000009764000
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF
→ ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentially causing a discharged battery and no-start condition.
DATA MONITOR
Signal buffer system
SIGNAL BUFFER
×
TPMS
AIR PRESSURE MONITOR
×
×
×
×
System
Sub System
Direct Diagnostic Mode
E
cu
Id
en
tifi
ca
tio
n
Se
lf Di
ag
no
st
ic Re
su
lt
Da
ta
Mo
ni
tor
A
cti
ve
T
est
W
o
rk
su
pp
ort
Co
nf
igu
rat
ion
CAN Diag
Support Mntr
Monitor Item [Unit]
Description
DOOR SW-DR [On/Off]
Indicates condition of front door switch LH.
DOOR SW-AS [On/Off]
Indicates condition of front door switch RH.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст