Nissan Pathfinder. Manual — part 364
DLK-222
< DTC/CIRCUIT DIAGNOSIS >
BACK DOOR CLOSURE MOTOR
BACK DOOR CLOSURE MOTOR
Diagnosis Procedure
INFOID:0000000009175784
Regarding Wiring Diagram information, refer to
.
1.
CHECK BACK DOOR CLOSURE MOTOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect back door lock assembly connector.
3. Check voltage between back door lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> Replace back door lock assembly. Refer to
DLK-308, "DOOR LOCK : Removal and Installation"
NO
>> GO TO 2.
2.
CHECK BACK DOOR CLOSURE MOTOR CIRCUIT
1. Disconnect automatic back door control module connector.
2. Check continuity between automatic back door control module harness connector and back door lock
assembly harness connector.
3. Check continuity between automatic back door control module harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control module. Refer to
DLK-321, "Removal and Installation"
.
NO
>> Repair or replace harness.
(+)
(–)
Condition
Voltage
(Approx.)
Back door lock assembly
Connector
Terminal
D557
1
Ground
Back door opener
switch
Pressed
16 – 7.8 V
2
Released
0 V
Automatic back door control module
Back door lock assembly
Continuity
Connector
Terminal
Connector
Terminal
B56
31
D557
1
Yes
38
2
Automatic back door control module
Ground
Continuity
Connector
Terminal
B56
31
No
38
AUTOMATIC BACK DOOR WARNING BUZZER
DLK-223
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
AUTOMATIC BACK DOOR WARNING BUZZER
Diagnosis Procedure
INFOID:0000000009175785
Regarding Wiring Diagram information, refer to
.
1.
CHECK BACK DOOR WARNING CHIME POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect back door warning chime connector.
3. Check voltage between back door warning chime harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BACK DOOR WARNING CHIME OUTPUT SIGNAL CIRCUIT
1. Disconnect automatic back door control module connector.
2. Check continuity between automatic back door control module harness connector and back door warning
chime harness connector.
3. Check continuity between automatic back door control module harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control module. Refer to
DLK-321, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK BACK DOOR WARNING CHIME GROUND CIRCUIT
Check continuity between back door warning chime harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK BACK DOOR WARNING CHIME
DLK-224, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace back door warning chime. Refer to
DLK-318, "Removal and Installation"
(+)
(–)
Voltage
(Approx.)
Back door warning chime
Connector
Terminal
B402
1
Ground
Battery voltage
Automatic back door control module
Back door warning chime
Continuity
Connector
Terminal
Connector
Terminal
B56
37
B402
1
Yes
Automatic back door control module
Ground
Continuity
Connector
Terminal
B56
37
No
Back door warning chime
Ground
Continuity
Connector
Terminal
B402
2
Yes
DLK-224
< DTC/CIRCUIT DIAGNOSIS >
AUTOMATIC BACK DOOR WARNING BUZZER
5.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
>> Inspection End.
Component Inspection
INFOID:0000000009175786
1.
CHECK BACK DOOR WARNING CHIME
1. Turn ignition switch OFF.
2. Disconnect back door warning chime connector.
3. Check battery power supply directly to back door warning chime terminals and check the operation.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace back door warning chime. Refer to
DLK-318, "Removal and Installation"
back door warning chime
Operation
Terminal
(+)
(-)
1
2
Chime sounds
GROUND CIRCUIT
DLK-225
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000009175787
Regarding Wiring Diagram information, refer to
.
1.
CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic back door control module connector.
3. Check continuity between automatic back door control module harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control module. Refer to
DLK-321, "Removal and Installation"
.
NO
>> Repair or replace harness.
Automatic back door control module
Ground
Continuity
Connector
Terminal
B56
32
Yes
28
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст