Nissan Pathfinder. Manual — part 1
ACC-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
ACC
A
ACC
N
O
P
CONTENTS
ACCELERATOR CONTROL SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . .
ACCELERATOR PEDAL ASSEMBLY . . . ...
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . ..
ACC-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009726118
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
ACCELERATOR PEDAL ASSEMBLY
ACC-3
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
ACC
N
P
O
REMOVAL AND INSTALLATION
ACCELERATOR PEDAL ASSEMBLY
Exploded View
INFOID:0000000009178440
Removal and Installation
INFOID:0000000009178441
REMOVAL
1. Remove three accelerator pedal assembly nuts.
2. Disconnect harness connector (A) from the accelerator pedal
assembly (1).
: Front
3. Remove the accelerator pedal assembly.
CAUTION:
• Do not disassemble accelerator pedal assembly.
• Do not drop or impact accelerator pedal assembly.
• Do not expose accelerator pedal assembly to water.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
For inspection, refer to
.
Inspection
INFOID:0000000009178442
INSPECTION AFTER INSTALLATION
1.
Accelerator pedal assembly
A. Nut
Front
ALBIA0775GB
ALBIA0776GB
ACC-4
< REMOVAL AND INSTALLATION >
ACCELERATOR PEDAL ASSEMBLY
• Check that the accelerator pedal moves smoothly within the speci-
fied range.
: Front
• Check the accelerator pedal height.
• Depress and release the accelerator pedal to check that it returns quickly and smoothly to the original
released position.
CAUTION:
• Whenever the harness connector of the accelerator pedal position sensor has been disconnected,
perform "Accelerator Pedal Released Position Learning". Refer to
• The accelerator pedal should operate smoothly without catching when the pedal operating force is
released. The pedal should return smoothly to the fully raised position. The spring should be free
from damage.
Accelerator pedal stroke (A) : Refer to
ALBIA0798ZZ
Accelerator pedal height
: Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст