Nissan Pathfinder. Manual — part 20
ADP-72
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription
INFOID:0000000009176544
Each function is reset to the following condition when the battery terminal is disconnected.
*1
: Default value is 40 mm.
NOTE:
Notice that disconnecting the battery when detected DTC are present will erase the DTC memory.
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Work
Procedure
INFOID:0000000009176545
1.
SYSTEM INITIALIZATION
Perform system initialization. Refer to
ADP-73, "SYSTEM INITIALIZATION : Work Procedure"
>> GO TO 2.
2.
MEMORY STORAGE
Perform memory storage. Refer to
ADP-74, "MEMORY STORING : Work Procedure"
>> GO TO 3.
3.
INTELLIGENT KEY INTERLOCK STORAGE
Perform Intelligent Key interlock storage. Refer to
ADP-75, "INTELLIGENT KEY INTERLOCK STORING :
>> GO TO 4.
4.
SYSTEM SETTING
Perform system setting. Refer to
ADP-75, "SYSTEM SETTING : Work Procedure"
>> Inspection End.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000009176546
Each function is reset to the following condition when the driver seat control unit is replaced.
Function
Condition
Procedure
Memory [Seat, steering (if equipped), mirror]
Erased
Perform storing
Entry/exit assist
ON
Perform initialization
Set slide amount
*1
Intelligent Key interlock
Erased
Perform initialization
Perform storing
Function
Condition
Procedure
Memory [Seat, steering (if equipped), mirror]
Erased
Perform storing
Entry/exit assist
ON
Perform initialization
Set slide amount
*1
INSPECTION AND ADJUSTMENT
ADP-73
< BASIC INSPECTION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
*1
: Default value is 40 mm.
NOTE:
Notice that disconnecting the battery when detected DTC are present will erase the DTC memory.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Work Procedure
INFOID:0000000009176547
1.
SYSTEM INITIALIZATION
Perform system initialization. Refer to
ADP-73, "SYSTEM INITIALIZATION : Work Procedure"
>> GO TO 2.
2.
MEMORY STORAGE
Perform memory storage. Refer to
ADP-74, "MEMORY STORING : Work Procedure"
>> GO TO 3.
3.
INTELLIGENT KEY INTERLOCK STORAGE
Perform Intelligent Key interlock storage. Refer to
ADP-75, "INTELLIGENT KEY INTERLOCK STORING :
>> GO TO 4.
4.
SYSTEM SETTING
Perform system setting. Refer to
ADP-75, "SYSTEM SETTING : Work Procedure"
>> Inspection End.
SYSTEM INITIALIZATION
SYSTEM INITIALIZATION : Description
INFOID:0000000009176548
Always perform the initialization when the battery terminal is disconnected or the driver seat control unit is
replaced.
The entry/exit assist function will not operate normally if no initialization is performed.
SYSTEM INITIALIZATION : Work Procedure
INFOID:0000000009176549
INITIALIZATION PROCEDURE
1.
CHOOSE METHOD
There are two initialization methods.
Which method do you use?
With door switch>>GO TO 2.
With vehicle speed>>GO TO 4.
2.
STEP A-1
Turn ignition switch from ACC to OFF position.
>> GO TO 3.
3.
STEP A-2
Driver door switch is ON (open)
→ OFF (close) → ON (open).
Intelligent Key interlock
Erased
Perform initialization
Perform storing
Function
Condition
Procedure
ADP-74
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
>> Inspection End.
4.
STEP B-1
Drive the vehicle at more than 25 km/h (16 MPH).
>> Inspection End.
MEMORY STORING
MEMORY STORING : Description
INFOID:0000000009176550
Always perform the memory storage when the battery terminal is disconnected or the driver seat control unit is
replaced. The memory function will not operate normally if no memory storage is performed.
MEMORY STORING : Work Procedure
INFOID:0000000009176551
Memory Storage Procedure
Two positions for the driver seat, steering column and outside mirror can be stored for memory operation by
following procedure.
1.
STEP 1
Check the following conditions.
• Ignition switch: ON
• CVT shift selector: P (Park) position
>> GO TO 2.
2.
STEP 2
Adjust driver seat, steering column (if equipped) and outside mirror position manually.
>> GO TO 3.
3.
STEP 3
1. Push set switch.
NOTE:
• Memory indicator for which driver seat position is already retained in memory is illuminated for 5 sec-
onds.
• Memory indicator for which driver seat position is not retained in memory is illuminated for 0.5 seconds.
2. Push the memory switch (1 or 2) for at least 1 second within 5 seconds after pushing the set switch.
NOTE:
• To enter driver seat positions into blank memory, memory indicator will be turned on for 5 seconds.
• To modify driver seat positions, memory indicator will be turned OFF for 0.5 seconds, then turned ON for
5 seconds.
NOTE:
If memory is stored in the same memory switch, the previous memory will be deleted.
>> GO TO 4.
4.
STEP 4
Confirm the operation of each part with memory operation.
>> Inspection End.
INTELLIGENT KEY INTERLOCK STORING
INTELLIGENT KEY INTERLOCK STORING : Description
INFOID:0000000009176552
Always perform the Intelligent Key interlock function storage when the battery terminal is disconnected or the
driver seat control unit is replaced. The Intelligent Key interlock function will not operate normally if no memory
storage is performed.
INSPECTION AND ADJUSTMENT
ADP-75
< BASIC INSPECTION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
INTELLIGENT KEY INTERLOCK STORING : Work Procedure
INFOID:0000000009176553
Intelligent Key Interlock Storage Procedure
Performing the following operation associates the registered driving position with Intelligent Key. When driver
door unlock operation is performed by Intelligent Key or driver door request switch, display of the registered
driving position and turnout operation can be performed.
1.
STEP 1
Check the following conditions.
• Ignition switch: OFF
• Initialization: done
• Driving position: registered
>> GO TO 2.
2.
STEP 2
1. Push set switch.
NOTE:
Memory indicator for which driver seat position is already retained in memory is illuminated for 5 seconds.
2. Push the Intelligent Key unlock button within 5 seconds after pushing memory switch (while the memory
indicator is turned ON).
NOTE:
From the time registration is performed, the applicable memory indicator blinks for 5 seconds.
>> GO TO 3.
3.
STEP 3
Confirm the operation of each part with memory operation and Intelligent Key interlock operation.
>> Inspection End.
SYSTEM SETTING
SYSTEM SETTING : Description
INFOID:0000000009176554
The settings of the automatic driving positioner system can be changed, using CONSULT, the display unit in
the center of the instrument panel and the set switch. Always check the settings before and after disconnect-
ing the battery terminal or replacing driver seat control unit.
Setting Change
×: Applicable
SYSTEM SETTING : Work Procedure
INFOID:0000000009176555
1.
CHOOSE METHOD
There are three setting methods.
Which method do you choose?
With CONSULT>>GO TO 2.
Item
Content
CONSULT
Set
switch
Factory
setting
Amount of seat sliding for
entry/exit assist
The amount of seat sliding for entry/exit assist can be
selected from 3 items.
[40 mm/80 mm/150 mm]
x
—
40 mm
Entry/exit assist
(seat)
Entry/exit assist (seat) can be selected:
ON (operated) – OFF (not operated)
x
x
ON
Entry/exit assist
[steering column (if equipped)]
Entry/exit assist (steering column) can be selected:
ON (operated) – OFF (not operated)
x
ON
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст