Nissan Pathfinder. Manual — part 1162
P0706 TRANSMISSION RANGE SENSOR A
TM-107
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10E]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• 10A fuse (No. 48, located in the IPDM E/R). Refer to
PG-85, "IPDM E/R Terminal Arrangement"
.
• IPDM E/R
Is the check result normal?
YES
>> Check intermittent incident. Refer to
GI-49, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Component Inspection
INFOID:0000000009177565
1.
CHECK TRANSMISSION RANGE SWITCH
Check continuity between transmission range switch connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to
214, "Removal and Installation"
Transmission range switch
Condition
Continuity
Terminal
7 – 10
Manual lever: “P” and “N” positions
Existed
Other than the above
Not existed
4 – 5
Manual lever: “P” position
Existed
Other than the above
Not existed
4 – 8
Manual lever: “R” position
Existed
Other than the above
Not existed
4 – 9
Manual lever: “N position
Existed
Other than the above
Not existed
4 – 2
Manual lever: “D” position
Existed
Other than the above
Not existed
4 – 6
Manual lever: “L” position
Existed
Other than the above
Not existed
TM-108
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10E]
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
DTC Logic (For North America)
INFOID:0000000009177566
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Turn ignition switch OFF and cool the engine.
2. Turn ignition switch ON.
CAUTION:
Never start the engine.
3. Select “Data Monitor” in “TRANSMISSION”.
4. Select “FLUID TEMP”.
5. Record CVT fluid temperature.
6. Start the engine and wait for at least 2 minutes.
7. Drive the vehicle for the total minutes specified in the Driving time column below with the following condi-
tions satisfied.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible causes
P0711
FLUID TEMP SENSOR A
(Transmission Fluid Tempera-
ture Sensor A Circuit Range/
Performance)
When any of 1 or 2 is satisfied:
1.
Under the following diagnosis conditions, CVT
fluid temperature does not rise to 10
°C (50°F)
after driving for a certain period of time with the
TCM-received fluid temperature sensor value
between
− 40°C (−40°F) and 9°C (48.2°F).
-
TCM power supply voltage: More than 11 V
-
CAN communication is normal
-
Engine speed: 450 rpm or more
-
Accelerator pedal position: 3 deg. or more
-
Vehicle speed: 10 km/h (7 MPH) or more
-
U0100, P0705 and P0706 are not detected.
-
Selector lever: “D” position
2.
When the condition of the final judgment is
satisfied after satisfying that of the provisional
judgment:
-
Provisional judgment: All of the following con-
ditions are satisfied within 2 seconds after the
ignition switch is turned ON.
•
U0073, U0100, P0712 and P0713 are not de-
tected.
•
CAN communication is normal.
•
TCM power supply voltage: More than 11 V
•
The difference between CVT fluid temperature
and engine coolant temperature is 55
°C
(131
°F) or more, or −27°C (−16°F) or less.
-
Final judgment: When all of the following con-
ditions are satisfied and this state is main-
tained for 300 seconds:
•
ECM is normal.
•
Provisional judgment is satisfied.
CVT fluid temperature sensor
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
TM-109
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10E]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
8. Stop the vehicle.
9. Check the first trip DTC.
With GST
1. Turn ignition switch OFF and cool the engine.
2. Start the engine and wait for at least 2 minutes.
3. Drive the vehicle and maintain the following conditions for 20 minutes or more.
4. Stop the vehicle.
5. Check the first trip DTC.
Is “P0711” detected?
YES
>> Go to
NO
>> GO TO 3.
3.
CHECK CVT FLUID TEMPERATURE SENSOR
1. Turn ignition switch OFF.
2. Disconnect CVT unit connector.
3. Check resistance between CVT unit connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of CVT fluid temperature sensor. Replace transaxle assembly. Refer to
TM-214, "Removal and Installation"
DTC Logic (Except for North America)
INFOID:0000000009774645
DTC DETECTION LOGIC
Selector lever
: “D” position
Accelerator pedal position
: 1.0/8 or more
Vehicle speed
: 10 km/h (7 MPH) or more
CVT fluid temperature before engine start
Driving time
−40°C (−40°F) – −31°C (−23.8°F)
20 minutes or more
−30°C (−22°F) – −21°C (−5.8°F)
18 minutes or more
−20°C (−4°F) – −11°C (−12.2°F)
14 minutes or more
−10°C (14°F) – −1°C (30.2°F)
10 minutes or more
0
°C (32°F) – 9°C (48.2°F)
7 minutes or more
Other than the above
—
(Go to 3.)
Selector lever
: “D” position
Accelerator pedal position
: 1.0/8 or more
Vehicle speed
: 10 km/h (7 MPH) or more
CVT unit
Condition
Resistance
(Approx.)
Terminal
12 – 18
CVT fluid temperature: 20
°C (68°F)
6.5 k
Ω
CVT fluid temperature: 50
°C (122°F)
2.2 k
Ω
CVT fluid temperature: 80
°C (176°F)
0.87 k
Ω
TM-110
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10E]
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PRECONDITIONING
1. Turn ignition switch ON.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “ATF TEMP SEN”.
Is “ATF TEMP SEN” value within 2.03 – 0.16 V?
YES
>> INSPECTION END
NO-1 (“ATF TEMP SEN” indicates 0.15 V or less.)>>Go to
.
NO-2 (“ATF TEMP SEN” indicates 2.04 V or more.)>>GO TO 3.
3.
CHECK DTC DETECTION
1. Start the engine.
2. Drive the vehicle.
3. Maintain the following conditions for 14 minutes or more.
4. Stop the vehicle.
5. Check the first trip DTC.
Is “P0711” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009177567
1.
CHECK CVT FLUID TEMPERATURE SENSOR
1. Turn ignition switch OFF.
2. Disconnect CVT unit connector.
3. Check resistance between CVT unit connector terminals.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible causes
P0711
FLUID TEMP SENSOR A
(Transmission Fluid Tempera-
ture Sensor A Circuit Range/
Performance)
When the temperature does not increase to the
specified temperature within a specified time after
all of the following conditions are satisfied:
• TCM power supply voltage: More than 11 V
• CAN communication is normal
• Engine speed: 450 rpm or more
• Accelerator pedal position: 3 deg. or more
• Vehicle speed: 10 km/h (7 MPH) or more
• U0100, P0705 and P0706 are not detected.
• Selector lever: “D” position
CVT fluid temperature sensor
Selector lever
: “D” position
Vehicle speed
: More than 10 km/h (7 MPH)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст