Nissan Pathfinder. Manual — part 346
DLK-150
< DTC/CIRCUIT DIAGNOSIS >
B2621 INSIDE ANTENNA
NO
>> GO TO 2.
2.
CHECK INSIDE KEY ANTENNA CIRCUIT
1. Disconnect BCM connector and inside key antenna (instrument center) connector.
2. Check continuity between BCM harness connector and inside key antenna (instrument center) harness
connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 2
1. Replace inside key antenna (instrument center). (New antenna or other antenna)
2. Connect BCM connector and inside key antenna (instrument center) connector.
3. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace inside key antenna (instrument center).
NO
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
BCM
Inside key antenna (instrument center)
Continuity
Connector
Terminal
Connector
Terminal
M80
123
M14
1
Yes
124
2
BCM
Ground
Continuity
Connector
Terminal
M80
123
No
124
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M80
123, 124
Ground
When Intelligent Key is in the an-
tenna detection area
When Intelligent Key is not in the
antenna detection area
JMKIA3839GB
JMKIA5951GB
B2622 INSIDE ANTENNA
DLK-151
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
B2622 INSIDE ANTENNA
DTC Logic
INFOID:0000000009175690
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Select INTELLIGENT KEY of BCM using CONSULT.
2. Select INSIDE ANT DIAGNOSIS in WORK SUPPORT mode.
3. Perform inside key antenna (INSIDE ANT DIAGNOSIS) on WORK SUPPORT of INTELLIGENT KEY.
4. Check BCM for DTC.
Is inside key antenna DTC detected?
YES
>> Refer to
DLK-151, "Diagnosis Procedure"
NO
>> Inside key antenna (console) is OK.
Diagnosis Procedure
INFOID:0000000009175691
Regarding Wiring Diagram information, refer to
.
1.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch OFF.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> GO TO 2.
DTC
CONSULT display
description
DTC detecting condition
Possible cause
B2622
INSIDE ANTENNA
An excessive high or low voltage from inside anten-
na (console) is sent to BCM.
• Inside key antenna (console)
• Harness or connector
[Inside key antenna (console) cir-
cuit is open or shorted]
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M80
116, 128
Ground
When Intelligent Key is in the an-
tenna detection area
When Intelligent Key is not in the
antenna detection area
JMKIA3839GB
JMKIA5951GB
DLK-152
< DTC/CIRCUIT DIAGNOSIS >
B2622 INSIDE ANTENNA
2.
CHECK INSIDE KEY ANTENNA CIRCUIT
1. Disconnect BCM connector and inside key antenna (console) connector.
2. Check continuity between BCM harness connector and inside key antenna (console) harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 2
1. Replace inside key antenna (console). (New antenna or other antenna)
2. Connect BCM connector and inside key antenna (console) connector.
3. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace inside key antenna (console). Refer to
DLK-315, "CONSOLE : Removal and Installation"
.
NO
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
BCM
Inside key antenna (console)
Continuity
Connector
Terminal
Connector
Terminal
M80
116
M255
1
Yes
128
2
BCM
Ground
Continuity
Connector
Terminal
M80
116
No
128
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M80
116, 128
Ground
When Intelligent Key is in the an-
tenna detection area
When Intelligent Key is not in the
antenna detection area
JMKIA3839GB
JMKIA5951GB
B2623 INSIDE ANTENNA
DLK-153
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
B2623 INSIDE ANTENNA
DTC Logic
INFOID:0000000009175692
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Select INTELLIGENT KEY of BCM using CONSULT.
2. Select INSIDE ANT DIAGNOSIS in WORK SUPPORT mode.
3. Perform inside key antenna (INSIDE ANT DIAGNOSIS) on WORK SUPPORT of INTELLIGENT KEY.
4. Check BCM for DTC.
Is inside key antenna DTC detected?
YES
>> Refer to
DLK-153, "Diagnosis Procedure"
NO
>> Inside key antenna (luggage room) is OK.
Diagnosis Procedure
INFOID:0000000009175693
Regarding Wiring Diagram information, refer to
.
1.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch OFF.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> GO TO 2.
DTC
CONSULT display
description
DTC detecting condition
Possible cause
B2622
INSIDE ANTENNA
An excessive high or low voltage from inside anten-
na (luggage room) is sent to BCM.
• Inside key antenna (luggage room)
• Harness or connector
[Inside key antenna (luggage
room) circuit is open or shorted]
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M20
100, 99
Ground
When Intelligent Key is in the an-
tenna detection area
When Intelligent Key is not in the
antenna detection area
JMKIA3839GB
JMKIA5951GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст