Nissan Pathfinder. Manual — part 610
EXL-128
< DTC/CIRCUIT DIAGNOSIS >
HAZARD SWITCH
3.
CHECK HAZARD SWITCH SIGNAL SHORT CIRCUIT
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-80, "Removal and Installation"
NO
>> Repair or replace the harness or connector.
4.
CHECK HAZARD SWITCH GROUND OPEN CIRCUIT
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace hazard switch. Refer to
EXL-148, "Removal and Installation"
NO
>> Repair or replace the harness or connectors.
Hazard switch
Ground
Continuity
Connector
Terminal
M26
2
No
Hazard switch
Ground
Continuity
Connector
Terminal
M26
3
Yes
EXTERIOR LIGHTING SYSTEM SYMPTOMS
EXL-129
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
SYMPTOM DIAGNOSIS
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000009175388
CAUTION:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected.
Symptom
Possible cause
Inspection item
Headlamp does not
switch to the high beam.
One side
• Fuse
• Harness between IPDM E/R
and the front combination lamp
• Harness between the front com-
bination lamp and ground
Headlamp (HI) circuit
Refer to
.
Both sides
—
Symptom diagnosis
BOTH SIDE HEADLAMPS DO
NOT SWITCH TO HIGH BEAM
Refer to
.
High beam indicator lamp is not turned ON (Head-
lamp switched to the high beam).
• BCM
• Combination meter
• Combination meter
Data monitor HI-BEAM IND
• BCM (HEAD LAMP)
Active test “HEADLAMP”
Headlamp does not switch to the low beam.
• Combination switch (lighting
and turn signal switch)
• Harness between the combina-
tion switch and BCM
• BCM
• IPDM E/R
Combination switch (lighting and
turn signal switch)
Refer to
.
High beam request signal
• BCM
• IPDM E/R
IPDM E/R
Data monitorHL HI REQ
Headlamp does not turn
ON.
One side
• Fuse
• Harness between IPDM E/R
and the front combination lamp
• Front combination lamp
• Harness between the front com-
bination lamp and ground
Headlamp (LO) circuit
Refer to
Both sides
—
Symptom diagnosis
BOTH SIDE HEADLAMPS (LO)
ARE NOT TURNED ON
Refer to
.
Headlamp does not turn
OFF.
When the ignition
switch is turned ON
• BCM
• Combination switch (lighting
and turn signal switch)
Combination switch (lighting and
turn signal switch) Refer to
.
The ignition switch is
turned OFF (After acti-
vating the battery sav-
er).
IPDM E/R
—
Headlamp is not turned ON/OFF with lighting switch
AUTO.
• Combination switch (lighting
and turn signal switch)
• Harness between combination
switch and BCM
• BCM
Combination switch
Refer to
.
• Optical sensor
• Harness between optical sen-
sor and BCM
• BCM
Optical sensor
Refer to
.
EXL-130
< SYMPTOM DIAGNOSIS >
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Daytime light system does not activate.
(if equipped)
• Fuse
• Harness between IPDM E/R
and the daytime light relay
• Harness between daytime light
relay and the daytime lamp
• Harness between the daytime
lamp and ground
• Daytime light bulb
• IPDM E/R
• Daytime light relay
• BCM
Symptom diagnosis
Daytime light system inoperative.
Refer to
Front fog lamp is not
turned ON.
One side
• Front fog lamp bulb
• Harness between IPDM E/R
and front fog lamp
• Front fog lamp
• IPDM E/R
Front fog lamp circuit
Refer to
Both sides
—
Symptom diagnosis
BOTH SIDE FRONT FOG LAMPS
ARE NOT TURNED ON
Refer to
Parking lamp is not turned
ON.
One side
• Parking lamp bulb
• Harness between IPDM E/R
and front/rear combination lamp
• Harness between front/rear
combination lamp and ground
• Front/rear combination lamp
• IPDM E/R
Parking lamp circuit
Refer to
Both sides
—
Symptom diagnosis
PARKING, LICENSE PLATE AND
TAIL LAMPS ARE NOT TURNED
ON
Refer to
Turn signal lamp does not
blink.
Indicator lamp is nor-
mal.
(The applicable side
performs the high flash-
er activation).
• Hazard BCM and each turn sig-
nal lamp
• Turn signal lamp bulb
Turn signal lamp circuit
Refer to
Turn signal indicator lamp
does not blink.
One side
Combination meter
—
Both sides
(Always)
• Turn signal indicator lamp sig-
nal
- BCM
• Combination meter
• Combination meter
Data monitor TURN IND
• BCM (FLASHER)
Active test FLASHER
Both sides
(Does blink when acti-
vating hazard warning
lamp with the ignition
switch OFF)
• Combination meter power sup-
ply and ground circuit
• Combination meter
Combination meter
Power supply and ground circuit
Refer to
.
• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating (Turn
signal is normal).
• Hazard switch
• Harness between the hazard
switch and BCM
• BCM
Hazard switch
Refer to
Symptom
Possible cause
Inspection item
NORMAL OPERATING CONDITION
EXL-131
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
NORMAL OPERATING CONDITION
Description
INFOID:0000000009175389
AUTO LIGHT SYSTEM
The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel,
sky bridge, shadowed area etc.) while using the auto light system. This causes for the control difference. This
is normal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст