Nissan Pathfinder. Manual — part 622
FRONT BUMPER
EXT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Section
Measurement
Minimum
Target Value
Maximum
A-A
Clearance
0.2 (0.01)
1.5 (0.06)
2.8 (0.11)
B-B
Clearance
0.5 (0.02)
2.0 (0.08)
3.5 (0.14)
B-B
Surface height
0.0 (0.00)
1.4 (0.06)
2.8 (0.11)
C-C
Clearance
1.0 (0.04)
2.0 (0.08)
3.0 (0.12)
C-C
Surface height
0.0 (0.00)
1.0 (0.04)
2.0 (0.08)
D-D
Clearance
0.0 (0.00)
0.0 (0.00)
0.0 (0.00)
D-D
Surface height
0.0 (0.00)
0.0 (0.00)
0.0 (0.00)
E-E
Clearance
-0.3 (-0.01)
0.0 (0.00)
0.7 (0.03)
F-F
Clearance
0.0 (0.00)
1.0 (0.04)
2.0 (0.08)
G-G
Clearance
-1.0 (-0.04)
0.0 (0.00)
1.0 (0.04)
H-H
Clearance
-0.8 (-0.03)
0.0 (0.00)
0.8 (0.03)
H-H
Surface height
-0.3 (-0.01)
0.7 (0.03)
1.7 (0.07)
J-J
Clearance
0.5 (0.02)
1.5 (0.06)
2.5 (0.10)
EXT-20
< REMOVAL AND INSTALLATION >
REAR BUMPER
REAR BUMPER
Exploded View
INFOID:0000000009176336
Removal and Installation
INFOID:0000000009176337
REMOVAL
CAUTION:
Bumper fascia is made of resin. Use care when handling to prevent damage. Avoid contact with oily
substances.
1. Open back door.
2. Remove the rear combination lamps (LH/RH). Refer to
EXL-149, "Removal and Installation"
.
1.
Rear bumper side bracket (LH)
2.
Rear bumper reinforcement
support (LH)
3.
Rear bumper fascia lower brack-
et (LH)
4.
Rear bumper reinforcement
5.
Rear bumper energy absorber 6.
Rear sonar sensor harness (if
equipped)
7.
Sonar sensors (if equipped)
8.
Tow hitch cover finisher
9.
Rear bumper fascia molding
10. Rear bumper fascia
11. Rear bumper fascia lower
bracket (RH)
12. Rear bumper reinforcement sup-
port (RH)
13. Rear bumper side bracket (RH)
AWKIA2252ZZ
REAR BUMPER
EXT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
3. Remove the rear bumper fascia clips (A) and screws (B) (LH/
RH).
4. Partially remove the rear wheel house protectors. Refer to
EXT-29, "REAR WHEEL HOUSE PROTEC-
TOR : Removal and Installation"
.
5. Remove the bumper fascia side upper screws (A) (LH/RH).
6. Remove rear bumper fascia lower side bolts (A) (LH/RH).
7. Remove the rear bumper fascia lower rear clips (A).
8. Disconnect the harness connector from rear sonar sensors (if equipped).
ALKIA2414ZZ
ALKIA2415ZZ
ALKIA2420ZZ
ALKIA2904ZZ
EXT-22
< REMOVAL AND INSTALLATION >
REAR BUMPER
9. Pull rear bumper fascia outward away from vehicle to release
from rear bumper side brackets (LH/RH).
: Pawl
10. Remove the rear bumper fascia.
CAUTION:
When removing rear bumper fascia, two people are required to avoid damaging.
11. Remove the following parts (if necessary) after removing rear bumper fascia.
• Rear bumper fascia reflectors (LH/RH)
• Rear sonar sensors (if equipped)
• Rear bumper fascia molding
12. Remove rear bumper energy absorber.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal
installation status.
• Fitting adjustment cannot be performed.
mm (in)
ALKIA2905ZZ
ALKIA2906ZZ
Section
Measurement
Minimum
Target Value
Maximum
A-A
Clearance
0.0 (0.00)
1.0 (0.04)
2.0 (0.08)
B-B
Clearance
0.0 (0.00)
1.5 (0.06)
3.0 (0.12)
C-C
Clearance
3.0 (0.12)
5.0 (0.20)
7.0 (0.28)
C-C
Surface height
-1.0 (-0.04)
1.0 (0.04)
3.0 (0.12)
D-D
Clearance
0.0 (0.00)
1.0 (0.04)
2.0 (0.08)
D-D
Surface height
-0.2 (0.01)
0.8 (0.03)
1.8 (0.07)
E-E
Clearance
5.0 (0.12)
7.0 (0.28)
9.0 (0.35)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст