Nissan Pathfinder. Manual — part 30

ADP-112

< DTC/CIRCUIT DIAGNOSIS >

DOOR MIRROR REMOTE CONTROL SWITCH

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace door mirror remote control switch. Refer to

MIR-22, "Removal and Installation"

.

MIRROR SWITCH
MIRROR SWITCH : Description

INFOID:0000000009176614

It operates angle of the door mirror face.

It transmits mirror face adjust operation to automatic drive positioner control unit.

MIRROR SWITCH : Component Function Check

INFOID:0000000009176615

1.

CHECK FUNCTION

1. Select “MIR CON SW-UP/DN”,“MIR CON SW-RH/LH “ in “DATA MONITOR” mode with CONSULT.

2. Check mirror switch signal under the following conditions.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Perform diagnosis procedure. Refer to

ADP-112, "MIRROR SWITCH : Diagnosis Procedure"

.

MIRROR SWITCH : Diagnosis Procedure

INFOID:0000000009176616

Regarding Wiring Diagram information, refer to

ADP-55, "WITH AROUND VIEW MONITOR : Wiring Diagram"

or

ADP-40, "WITHOUT AROUND VIEW MONITOR : Wiring Diagram"

.

1.

CHECK MIRROR SWITCH FUNCTION

1. Turn ignition switch ON.

2. Check voltage between automatic drive positioner control unit connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 2.

2.

CHECK HARNESS CONTINUITY

Monitor item

Condition

Status

MIR CON SW-UP/DN

Mirror switch (up/down)

Operate

ON

Release

OFF

MIR CON SW-RH/LH

Mirror switch (right/left)

Operate

ON

Release

OFF

(+)

(–)

Mirror switch

Condition

Voltage (V)

(Approx.)

Automatic drive positioner con-

trol unit

Connector

Terminal

M33

3

Ground

UP

0

Other than above

5

4

LEFT

0

Other than above

5

15

DOWN

0

Other than above

5

16

RIGHT

0

Other than above

5

DOOR MIRROR REMOTE CONTROL SWITCH

ADP-113

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

1. Turn ignition switch OFF.

2. Disconnect automatic drive positioner control unit and door mirror remote control switch.

3. Check continuity between automatic drive positioner control unit connector and door mirror remote control

switch connector.

4. Check continuity between automatic drive positioner control unit connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT

Check continuity between door mirror remote control switch connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK MIRROR SWITCH

Check mirror switch.

Refer to

ADP-113, "MIRROR SWITCH : Component Inspection"

.

Is the inspection result normal?

YES

>> Refer to

GI-49, "Intermittent Incident"

.

NO

>> Replace door mirror remote control switch. Refer to

MIR-22, "Removal and Installation"

.

5.

CHECK INTERMITTENT INCIDENT

Check intermittent incident.

Refer to

GI-49, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit. Refer to

ADP-162, "Removal and Installation"

.

NO

>> Repair or replace the malfunctioning parts.

MIRROR SWITCH : Component Inspection

INFOID:0000000009176617

1.

CHECK MIRROR SWITCH

Check door mirror remote control switch.

Automatic drive positioner con-

trol unit

Door mirror remote control switch

Continuity

Connector

Terminal

Connector

Terminal

M33

3

D22

12

Yes

4

1

15

16

16

9

Automatic drive positioner control unit

Ground

Continuity

Connector

Terminal

M33

3

No

4

15

16

Door mirror remote control switch

Ground

Continuity

Connector

Terminal

D22

15

Yes

ADP-114

< DTC/CIRCUIT DIAGNOSIS >

DOOR MIRROR REMOTE CONTROL SWITCH

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace door mirror remote control switch. Refer to

MIR-22, "Removal and Installation"

.

Terminal

Mirror switch condition

Continuity

Door mirror remote

control switch

9

15

RIGHT

Yes

Other than above

No

1

LEFT

Yes

Other than above

No

12

UP

Yes

Other than above

No

16

DOWN

Yes

Other than above

No

POWER SEAT SWITCH GROUND CIRCUIT

ADP-115

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

POWER SEAT SWITCH GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000009176618

Regarding Wiring Diagram information, refer to

ADP-55, "WITH AROUND VIEW MONITOR : Wiring Diagram"

or

ADP-40, "WITHOUT AROUND VIEW MONITOR : Wiring Diagram"

.

1.

CHECK POWER SEAT SWITCH LH GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect power seat switch LH.

3. Check continuity between power seat switch LH connector and ground.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-49, "Intermittent Incident"

.

NO

>> Repair or replace harness.

Power seat switch LH

Ground

Continuity

Connector

Terminal

B208

3

Yes