Nissan Pathfinder. Manual — part 29
ADP-108
< DTC/CIRCUIT DIAGNOSIS >
SEAT MEMORY SWITCH
4. Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace driver seat control unit. Refer to
ADP-161, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK MEMORY SWITCH GROUND CIRCUIT
Check continuity between seat memory switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK SEAT MEMORY SWITCH
ADP-108, "Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-49, "Intermittent Incident"
.
NO
>> Replace seat memory switch. Refer to
ADP-163, "Removal and Installation"
.
Component Inspection
INFOID:0000000009176609
1.
CHECK SEAT MEMORY SWITCH
1. Turn ignition switch OFF.
2. Disconnect seat memory switch.
3. Check continuity between seat memory switch terminals.
Is the inspection result normal?
YES
>> Inspection End.
Driver seat control unit
Seat memory switch
Continuity
Connector
Terminal
Connector
Terminal
B209
11
D60
16
Yes
21
2
27
10
Driver seat control unit
Ground
Continuity
Connector
Terminal
B209
11
No
21
27
Seat memory switch
Ground
Continuity
Connector
Terminal
D60
9
Yes
Terminal
Condition
Continuity
Seat memory switch
9
10
Memory switch 1
Push
Yes
Release
No
16
Memory switch 2
Push
Yes
Release
No
2
Set switch
Push
Yes
Release
No
SEAT MEMORY SWITCH
ADP-109
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
NO
>> Replace seat memory switch. Refer to
ADP-163, "Removal and Installation"
.
ADP-110
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
DOOR MIRROR REMOTE CONTROL SWITCH
CHANGEOVER SWITCH
CHANGEOVER SWITCH : Description
INFOID:0000000009176610
Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.
CHANGEOVER SWITCH : Component Function Check
INFOID:0000000009176611
1.
CHECK FUNCTION
1. Select “MIR CHNG SW-R”, “MIR CHNG SW-L” in “DATA MONITOR” mode with CONSULT.
2. Check changeover switch signal under the following conditions.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Perform diagnosis procedure. Refer to
ADP-110, "CHANGEOVER SWITCH : Diagnosis Proce-
.
CHANGEOVER SWITCH : Diagnosis Procedure
INFOID:0000000009176612
Regarding Wiring Diagram information, refer to
ADP-55, "WITH AROUND VIEW MONITOR : Wiring Diagram"
or
ADP-40, "WITHOUT AROUND VIEW MONITOR : Wiring Diagram"
.
1.
CHECK CHANGEOVER SWITCH SIGNAL
1. Turn ignition switch ON.
2. Check voltage between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mirror remote control switch.
3. Check continuity between automatic drive positioner control unit connector and door mirror remote control
switch connector.
Monitor item
Condition
Status
MIR CHNG SW-R
Mirror switch (right)
Operate
ON
Release
OFF
MIR CHNG SW-L
Mirror switch (left)
Operate
ON
Release
OFF
(+)
(-)
Change over switch
condition
Voltage (V)
(Approx.)
Automatic drive positioner con-
trol unit
Connector
Terminal
M33
2
Ground
RIGHT
0
Other than above
5
14
LEFT
0
Other than above
5
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-111
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
4. Check continuity between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
Check continuity between door mirror remote control switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK CHANGEOVER SWITCH
Check changeover switch.
ADP-111, "CHANGEOVER SWITCH : Component Inspection"
Is the inspection result normal?
YES
>> Refer to
GI-49, "Intermittent Incident"
.
NO
>> Replace door mirror remote control switch. Refer to
MIR-22, "Removal and Installation"
5.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
GI-49, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-162, "Removal and Installation"
.
NO
>> Repair or replace the malfunctioning parts.
CHANGEOVER SWITCH : Component Inspection
INFOID:0000000009176613
1.
CHECK CHANGEOVER SWITCH
Check door mirror remote control switch.
Automatic drive positioner control
unit
Door mirror remote control switch
Continuity
Connector
Terminal
Connector
Terminal
M33
2
D22
3
Yes
14
4
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M33
2
No
14
Door mirror remote control switch
Ground
Continuity
Connector
Terminal
D22
15
Yes
Terminal
Change over switch
condition
Continuity
Door mirror remote control switch
3
15
LEFT
Yes
Other than above
No
4
RIGHT
Yes
Other than above
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст